Heath Zenith 5105 - Manual
Heath Zenith 5105 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – INSTALLATION; Wall Mount; Timer; Mode Switching Summary; MANUAL MODE
- Page 3 – Mount the Light Control; WARNING: Turn power off at circuit breaker
- Page 4 – Maximum; TEST AND ADJUSTMENT
- Page 5 – SPECIFICATIONS; TROUBLESHOOTING GUIDE
- Page 6 – TECHNICAL SERvICE; No Service Parts Available for this Product
- Page 7 – FUNCIONAMIENTO; Características; Requisitos
- Page 8 – Resumen de las modalidades del interruptor; PRUEBA; Luz de Adorno; INSTALACION; Montaje en pared
- Page 9 – Conecte el Control de Luz; ADvERTENCIA: Desconecte la energía en el; Instale el Control de Luz
- Page 10 – Parte de abajo del detector; Lo menos sensible; PRUEBA Y AJUSTE
- Page 11 – ESPECIFICACIONES; GUIA DE INvESTIGACION DE AvERIAS
- Page 12 – GARANTÍA LIMITADA A 10 AÑOS; SERvICIO TÉCNICO; de devolver el producto a la tienda.; No hay piezas de servicio disponibles para este producto.
- Page 13 – ESSAI; FONCTIONNEMENT; AUTOMATIQUE
- Page 14 – Résumé du mode de commutation; PRIORITÉ MANUELLE; Minuterie D; Montage sous
- Page 16 – Bas du détecteur; Portée maximale; ESSAIS ET RÉGLAGES
- Page 17 – FICHE TECHNIQUE; GUIDE DE DÉPANNAGE
- Page 18 – GARANTIE LIMITÉE DE 10 ANS; Exclusions de la garantie -; SERvICE TECHNIQUE; avant de retourner l’article au magasin.; Aucune pièce de rechange n’est disponible pour ce produit.
© 2008 HeathCo LLC
598-1102-06
Model 5105
Motion Sensor
Light Control
TEST
2 Shells
Features
• Creep Zone™ Technology.
• Turns on lighting when motion is detected.
• Automatically turns lighting off.
• D
ual
B
rite
®
Timer.
• Photocell keeps the lighting off during daylight hours.
• LED indicates motion was sensed (day or night).
TEST
1 5 20
ON-TIME
Off
3 6 Dusk to
Dawn
D
ual
B
rite
®
Put ON-TIME switch
on the sensor bottom
to TEST and the D
ual
-
B
rite
®
switch OFF.
OPERATION
* resets to Auto Mode at dawn.
ON-TIME
TEST
1 5 20
... back on.
1 Second OFF
then...
Put the ON-TIME switch in the 1, 5,
or 20 minute position.
Manual mode only works at night
because daylight returns the sensor
to AUTO.
Flip the light switch off for one second
then back on to toggle between AUTO
and MANUAL MODE.
Manual mode works only with the
ON-TIME switch in the 1, 5, or 20
position.
Note:
When first turned on wait about 1
1
/
2
minutes for
the circuitry to calibrate.
This package includes:
Light Control
Sensor
Cover
Plate
Bulb
Holders
Plastic Hanger
Rubber Plug
Gasket
6 Screws
(3 sizes included)
Mounting Strap
Mounting Bolt
2 Wire
Connectors
Requirements
• The light control requires 120-volts AC.
• If you want to use Manual Mode, the control must be
wired through a switch.
•
Some codes require installation by a qualified
electrician.
• This product is intended for use with the enclosed
gasket and with a junction box marked for use in wet
locations.
Mode:
On-Time
Works: Day Night
Test
5 Seconds
x
x
Auto
1, 5, or 20 Min
x
Manual
To Dawn*
x
Accent
3, 6 Hr, to Dawn
x
AUTO
MANUAL MODE
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 598-1102-06 INSTALLATION For easy installation, select an existing light with a wall switch for replacement.For best performance, mount the fixture about 8 ft. (2.4 m) above the ground. NOTE: If fixture is mounted higher than 8 ft. (2.4 m), aiming the sensor down will reduce coverage distance. For...
3 598-1102-06 ❒ Remove the existing light fixture. ❒ Install the mounting strap as shown using two screws that fit your junction box. ❒ The plastic hanger can be used to hold the fixture while wiring. The small end of the plastic hanger can be threaded through the hole in the center of the cover pla...
4 598-1102-06 ❒ Loosen the clamp screw in the sensor ball joint and gently rotate the sensor. ❒ Walk through the coverage area noting where you are when the lights turn on (also, the LED will flash several times when motion is detected). Move the sensor head up, down, or sideways to change the cover...
