GE ZIF360NHCLH - Installation Manual

31-49140-1 Design Guide - Standard Installation 36" Frame to Frame Width *84" FromFloor toTop Frame 35" Case Width *83-1/2" at Rear 25-3/8" Case Depth Depth Including Handles 26-7/8" THE INSTALLATION SPACE Water And Electrical Locations Electrical and water supply must be loc...

31-49140-1 Design Guide - Standard Installation 7 These units are equipped with a 3-position door stop. The factory set 115° door swing can be adjusted to 90° or 130° if clearance to adjacent cabinets or walls is restricted. Order WX14X99 door stop for precise settings between 90° and 130°. When Ins...

31-49140-1 Design Guide - Standard Installation 8 CUSTOMIZATION BASICS: Framed or Overlay Panels, Custom Handles and Accessory Kits Trimmed models are designed to be customized with decorative panels. Field installed custom door and grille panels are required. Optional Accessory Kits • ZKHSS2: Monog...

31-49140-1 10 SIDE PANELS Side panels must be used whenever the sides of the unit will be exposed. The 1/4” (0.63 cm) side panels will slip into the side case trim. Secure the panels to the unit with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.• Cut a ...

31-49140-1 Installation Instructions - Standard Installation 12 HARDWARE SUPPLIED • Water filter bypass plug• Anti-Tip brackets• 3 lag screws• 2 Hair Pin Cotters• 4 washers• 5 toggles with bolts• Toekick TOOLS AND MATERIALS REQUIRED • Tin snips to cut banding• #2 Phillips screwdriver• Stepladder • D...

31-49140-1 Installation Instructions - Standard Installation 13 STEP 1 REMOVE PACKAGING WARNING Tip Over Hazard. Product is much heavier at the top than at the bottom – be careful when moving. When using a hand truck, handle from side only. AVERTISSEMENT Risque de basculement Le produit est beaucoup...

31-49140-1 • Place the bottom of the wall bracket with tabs on the horizontal line. Align the center notch on the bracket with the center line on the wall. • The anti-tip wall bracket has a series of holes. Select 2 holes that match with the located studs. Make sure the holes selected are on the cen...

31-49140-1 Installation Instructions - Standard Installation 16 Remove Grilles for Access to Anti-Tip Locking Hooks Fresh Food Unit • Open the access door.• Remove the 4 screws from the grille on the right and 3 screws from the grille on the left. • Pull the bottom of the grilles forward, down and o...

31-49140-1 17 Installation Instructions - Standard Installation STEP 5 LEVEL UNIT All models have 4-point leveling. The front is support-ed by leveling legs; the rear is supported by adjustable wheels. Both are accessible from the front of the unit.• To level the back of the unit, turn the 7/16” hex...

31-49140-1 Installation Instructions - Standard Installation 18 STEP 7 ADJUST DOOR SWING NOTE: This appliance has a 3-position door stop. When space does not allow the door to swing open fully to 115°, you may change the door swing to a 90° opening. A 130° door swing is available for stan-dard insta...

Installation Instructions - Standard Installation 19 STEP 9 INSTALL FRAMED PANELS • There are two sets of holes in the handle side trim. Replace the handle side trim by installing the original screws in the FRONT screw holes. • Secure the handle to the door using the REAR screw holes. Use Rear Holes...

Installation Instructions - Standard Installation 20 STEP 9A INSTALL OVERLAY PANELS • There are two sets of holes in the handle side trim. Replace the handle side trim by installing the original screws in the REAR screw holes. • Secure the handle to the door using the FRONT screw holes. Custom Handl...

STEP 10 CONNECT WATER SUPPLY (FREEZER MODELS ONLY) WARNING Connect to potable water supply only. AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. • Locate and bring the tubing to the front of the cabinet.• Turn the water on to flush debris from the line. Run about a qua...

Design Guide - Flush Installation 23 38-3/4" Frame to Frame Width *84" FromFloor toTop Frame 35" Case Width *83-1/2" at Rear 25-3/8" Case Depth Depth Including Handles 26-7/8" THE INSTALLATION SPACE Water And Electrical Locations Electrical and water supply must be located as...

Design Guide - Flush Installation These units are equipped with a 3-position door stop. The factory set 115° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls is restricted. When Installed into a corner: Allow 15” (38.1 cm) for a full 115° door swing and pan removal. Allow...

25 Design Guide - Flush Installation 1/2” (1.27 cm) OVERLAY PANEL DIMENSIONS For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a 1/4” (.63 cm) thick backer panel which slides into the trim. A spacer panel 0.10” (0.25 cm) thick must ...

30 SIDE PANELS Side panels must be used whenever the sides of the unit will be exposed. The 1/4” (0.63 cm) side panels will slip into the side case trim. Secure the panels to the unit with stick-on hook and loop fastener strips. Order the side panels from the cabinet manufacturer.• Cut a notch in th...

Installation Instructions - Flush Installation 31 HARDWARE SUPPLIED • Water filter bypass plug• Anti-Tip brackets• 3 lag screws• 2 Hair Pin Cotters• 4 washers• 5 toggles with bolts• Toekick• Flush install case trim TOOLS AND MATERIALS REQUIRED • Tin snips to cut banding• #2 Phillips screwdriver• Ste...

Installation Instructions - Flush Installation 32 STEP 3 INSTALL SIDE PANELS Skip this step when not using side panels If you are using 1/4” (0.63 cm) side panels, they should be inserted into the case trim. Fasten the panels to the unit with stick-on hook and loop fastener strips before setting uni...

Installation Instructions - Flush Installation 33 STEP 4 INSTALL CASE TRIM The unit arrives with case trim for standard installation attached. Flush installation case trim is provided. Remove the factory installed case trim. Install new case trim using supplied right hand and left hand case trim pie...

• Mark an additional hole at each end of the bracket. If one of the studs is closer to the end of the bracket, mark an additional hole towards the center of the bracket. • Drill 1/2” (1.27 cm) holes into the wall board at the locations marked for the toggles to be mounted (not the stud markings). • ...

Installation Instructions - Flush Installation 35 Remove Grilles for Access to Anti-Tip Locking Hooks Fresh Food Unit • Open the access door.• Remove the 4 screws from the grille on the right and 3 screws from the grille on the left. • Pull the bottom of the grille forward, down and out to remove. F...

STEP 7 ADJUST DOOR SWING NOTE: This appliance has a 3-position door stop. When space does not allow the door to swing open fully to 115°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfac- tory for your installation situation. • Open the grille to view the to...

Custom Handles • Custom handles must be used for flush installation. The handle must be properly secured to the overlay panel before sliding the panel into the trim. • The cabinet manufacturer will supply the custom handle and hardware. • Discard the supplied handle.• Slide assembled door panel into...

Design Guide - Stainless Steel Installation 40 36" Frame to Frame Width *84" From Floor to Top Frame 35" Case Width *83-1/2" at Rear 25-3/4" Stainless Steel Models Case Depth Depth Including Handles: 27-5/8" Stainless Steel Models 28-5/8" Professional Models THE INSTALLAT...

42 Design Guide - Stainless Steel Installation CUSTOMIZATION BASICS: Custom Handles and Accessory Kits Professional Style Stainless Steel Models Stainless steel wrapped refrigerators have beveled edges and professional-style handles. These models are shipped ready for installation. Stainless Steel W...

Installation Instructions - Stainless Steel Installation 44 HARDWARE SUPPLIED • Water filter bypass plug• Anti-Tip brackets• 3 lag screws• 2 Hair Pin Cotters• 4 washers• 5 toggles with bolts• Toekick TOOLS AND MATERIALS REQUIRED • Tin snips to cut banding• #2 Phillips screwdriver• Stepladder • Drill...

• The kit supplied with the unit contains 2 lag bolts and 4 toggles with bolts. The wall bracket will be attached to the wall in 4 places. • Measure the opening where the unit is to be installed. Mark the center with a vertical line. • Measure up 81 1/2 (207.01) from the floor. Mark this point on th...

Installation Instructions - Stainless Steel Installation 48 Move Unit into Final Position • Move appliance toward its final installed location. Align the tabs on the wall bracket with the openings in the back of the unit. • The unit has “L” bolts in the upper left and right cor- ners inside of the a...

49 Installation Instructions - Stainless Steel Installation STEP 6 SECURE UNIT TO WALL • The “L” rods can be found in the upper left and right corners of the unit in the access compartment. Look through the access compartment to make sure the rods line up with the anti-tip bracket. • There are 2 was...

50 STEP 8 CONNECT WATER SUPPLY (FREEZER MODELS ONLY) WARNING Connect to potable water supply only. AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. • Locate and bring the tubing to the front of the cabinet. • Turn the water on to flush debris from the line. Run about a ...