Page 2 - Contents; CAUTION
CAUTION Before you begin – Read these instructions completely and carefully. IMPORTANT – Save these instructions for local inspector’s use. IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep these...
Page 3 - Design Information; Side Panel Requirements:; Advance Planning; DESIGN
3 Design Information 36" Refrigerators, Freezers Flush orSemi-FlushEnclosureInstallations Side Panel Requirements: • Side panels are not required whenever the refrigerator is installed into an enclosure or betweenpantry and oven cabinets. • Side panels are required whenever the sides of the refr...
Page 4 - • Electrical and water locations must; Freezer; Clearances; When Installed into a corner:; Clearances for Multiple Single Door Installations; ZUG75 Grille Panel Kit will not fit this installation.
4 For a complete food storage center,install a Monogram Freezer andRefrigerator side by side. Order ZUG75Unified Grille Panel Kit for one continuous 3/4" panel. • Electrical and water locations must be located as shown for either type ofinstallation. A separate 115V, 60Hz. 20amp power supply is ...
Page 5 - Edge Flush With Cabinet; Refrigerator or Freezer
5 Installation At End-of-Run FramelessCabinets NOTE: 1/2" thick side panels shown. Side panels can be any thickness.Add side panel thickness to outsidetrim width, (36” or 72" for two models) to calculate the rough-indimension. The leading (front) edge must be finished to matchsurrounding cab...
Page 7 - IMPORTANT; Optional Custom Trim Kits:; When installed into a corner:; Custom Panel Dimensions
7 ZIR36N RefrigeratorZIF36N Freezer Design Information Designed to be installed flush or semi-flush withsurrounding cabinetry. Cutout dimensions, clearancesand side panel sizes are determined by the manyinstallation options available. Side panels must be usedwhenever the sides of the refrigerator wi...
Page 8 - Custom Door Panel Dimensions Using Standard Trim; or; CUSTOM P
8 Custom Door Panel Dimensions Using Standard Trim 1/4" thick panels or Panels secured to 1/4" thick backing ZIR36N RefrigeratorZIF36N Freezer • 1/4" Panel: Cut panels to size.• Custom handle with 1/4" door panel requires Trim kits ZKHR1 or ZKHRSS1 for tubular stainless steel handles...
Page 9 - • The ZKTR36LH (or ZKTR36RH) trim kit provides for the; Custom Door Panel Dimensions; Using Trim Kits ZKTR36LH or ZKTR36RH; Installation Height; maximum grille panel weight is 9 lbs.
9 ZIR36N RefrigeratorZIF36N Freezer • The ZKTR36LH (or ZKTR36RH) trim kit provides for the installation of 3/4" thick custom door and grille panels,using the supplied handle. Cut panel to size and install. Custom Door Panel Dimensions Using Trim Kits ZKTR36LH or ZKTR36RH 3/4" thick panel wit...
Page 10 - • The ZKTR36LH (or ZKTR36RH) trim kit installed; Using Trim Kit ZKTR36LH or ZKTR36RH
10 ZIR36N RefrigeratorZIF36N Freezer • The ZKTR36LH (or ZKTR36RH) trim kit installed together with a ZKHTR1 custom handle kit provides for the installation of 3/4" thick custom door and grillepanels with a custom handle of your choice. OrderZKHTRSS1 for a tubular stainless steel handle. Cut pane...
Page 11 - Trim; Side Panel or Filler Options; Side panels must be used whenever the sides of the; Top View
23 5/16" 84" 2 5/16" 24 3/4" 84" 3 3/4" 23 9/16" 84" 2 9/16" Trim 11 1/4" Side PanelsInsert end of side panel into trim.Use stick-on hook andloop fastener strips tosecure the panel to therefrigerator. Standard 4" high toekick or trim to fit.Height may vary...
Page 12 - Flooring; Use of Extension Cords; Installation
12 ToolsRequired • Tinsnips to cut banding• Stepladder• 1-1/4" open-end wrench • Bucket• Level• Appliance Hand Truck• Tubing cutter • 7/16" open-end wrench• #2 Phillips screwdriver• Stubby Phillips screwdriver • Drill and appropriate bits• 7/16" socket with 3" extension for ratchet •...
Page 14 - Shut off the main water supply.; Floor
14 Step 2InstallWater Line • Install optional water filter in the water line near the refrigerator. A water filter is recommended in areaswhere water supply contains sand or particles.Installation instructions are packed with the filter. • A cold water supply is required for automatic icemaker opera...
Page 16 - GE SmartConnectTM Tubing:; If you attempt to raise the
16 Step 5LevelRefrigeratoror Freezer All models have 4-point leveling. The front is supportedby leveling legs, the rear is supported by wheels.• Adjust rear wheels beneath the product to just barely touch the 2x4 block. • Turn the 7/16" hex nut located above the front wheels. Turn to raise or lo...
Page 17 - To insert custom grille panel into the frame:; and bottom of panel frame.
17 Step 9CheckPower • Check to make sure power is on by opening the door to see if interior lights are on. If you are using a 3/4" thick custom panel, SKIP THISSTEP. See Dimensions and Specifications for grillepanel sizes. Order ZKTR36LH or ZKTR36RH and followthe installation instructions packed...
Page 18 - Door Hinge
18 Step 13StartIcemaker • A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and tighten screws. IMPORTANT: The vented toekick must remain unobstructed for proper air circulation and operation. Step 14Install Toekick Step 12Arrange Interior and SetTemperatureCon...
Page 19 - To change grille panel size:; and bottom of grille panel.; gap; ZGC2 Trim Kit; Grille Panel Frame Adjustment
19 This kit provides optional side trim pieces for the original grille panel frame to fit 83-1/2" and 84-1/2"installation heights. To change grille panel size: • Determine the installation height by measuring the enclosure from the floor to the underside of soffit.When there is no soffit, me...
Page 20 - Support for Custom Handles
20 Tools and materials required:• #2 Phillips screwdriver• Drill and appropriate bits• Custom door panel• Custom Handle• Safety glasses Parts List: A. Handle side door extrusion (for left hand models)B. Handle side door extrusion (for right hand models) This kit provides the necessary framework to i...
Page 22 - Parts List; Kit Contents
22 Right hand door swing models are illustrated in theseinstructions. Follow these instructions for left handmodels. Tools and materials required: • #2 Phillips screwdriver• Drill and appropriate bits • Custom door panels• Putty knife• Safety glasses• 7/16" wrench Parts List A. Top trimB. Handle...
Page 24 - Screws
24 Step 5Installhandles Step 6Adjustgrille panel height • Install new door handle using original screws. • Secure the grille panel support to the back side of the 3/4" custom panel with #6 screws. • Be sure the lip of the support is over the top of the wood panel. Step 7Secure 3/4"panel togr...
Page 26 - and to install panel support brackets.; Tools and materials required:; This kit must be used in combination with ZKTR36LH; of your choice; Optimal final appearance depends on careful; Back Side
26 3/4" custom door panel must be routed to accommodatethese door handle extrusions. Rout the panel asillustrated, 1/4" deep, and 1-13/16" wide on the handleside. Refer to installation instructions for ZKTR36LH orZKTR36RH trim kit for 3/4" custom panels:• Follow Step 1 to remove the ...
Page 27 - Screw
27 • Place the prepared 3/4" custom door panel on the bottom trim with support bracket tabs inserted intotrim slots. • Push the panel back against the steel door, making sure the panel is flush with the hinge side trim. • Secure the panel to the trim temporarily by driving 2 screws through the b...
Page 29 - It is best that 2 people install this kit.; floor when drilling
29 Step 1Remove handle Right hand door swing models are illustrated in theseinstructions. Follow these instructions for left hand models. NOTE: It is best that 2 people install this kit. Tools and materials required: • #2 Phillips screwdriver• Drill and appropriate bits• Custom door panel• Safety gl...
Page 30 - Step 2A; Tubular Stainless Steel Handles
30 Step 2Matchhandle extrusionsto handle FOR CUSTOM WOOD PANELS See Step 2A for Stainless Steel panels • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2" thick section of plywood toprotect flooring when drilling. • Place custom panel on the pad, appearance side dow...
Page 32 - FOR; Panels have a protective plastic covering. Peel
32 Raised Panel on 1/4" Thick Backing: A raised panel design secured to a 1/4" thick backing(screwed or glued) can be used with this handle kit.• Cut the 1/4" thick panels to size.• Fabricate the raised panel to allow 1-1/4" clearance from the hinge side of the panel to avoid strikin...
Page 34 - It is best that 2 people perform this step.
34 Step 1Match HandleExtrusionto Panel • Cut a piece of corrugated to use as a pad to protect the panel finish. Additional material may be required to protect flooring when drilling. • Place custom panel on the pad, appearance side down. • Select handle extrusion for your model, left or right side e...
Page 35 - Tools and materials Required:; ZUG75 Trim Kit
35 This kit provides for the installation of a 3/4" thick custom grille panel to span the combined width of aside by side installation. Use this kit in combination with 3/4" custom panel kits, ZKTR36LH and ZKTR36RH. Tools and materials Required: • #1 and #2 Phillips screwdrivers or sockets• ...
Page 36 - ATTENTION
36 • Cut a 2"x4" block, 71" long. Secure the 2"x4" to the 4 mounting brackets provided using #12 or #14 woodscrews. • Secure the brackets with wood block to the back wall so that it is 84" (or your installation height) from the finished floor. Use #12 or #14 wood screws. Seei...
Page 40 - For Monogram; • To lower the door, turn hinge pin towards the left.
Pub. No. 49-60055-3Dwg. No. 197D2785P001 12-03 JR 65160-01 NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Th...
