GE ZICP360NHDRH - Installation Manual

Instructions for Standard Installation 5 31-49142-1

THE INSTALLATION SPACE Water And Electrical Locations Electrical and water supply must be located as shown. The Cutout Depth Must Be 24” (60.96 cm) The refrigerator will project forward, slightly beyond adjacent cabinetry, depending on your installation. Allow minimum 1/8” (0.32 cm) air gap between ...

CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits These refrigerators are designed to be customized with decorative panels. Field installed custom door and grille panels are required. Side Panels Side panels must be used whenever the sides of the refrigerator will be ...

1/4” (0.63 cm) FRAMED PANEL DIMENSIONS If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slide into the frame on the door, drawer and grille.If the custom panel is less than 1/4” thick and if it fits loosely in the door frame, it can be backed up with ...

ZUG2 GRILLE PANEL DIMENSIONS The ZUG2 unified grille panel kit provides for the installation of a framed or overlay grille panel. Assemble the overlay panels in the same manner as the door and drawer panels. Design Guide - Standard Installation 9 SIDE PANELS Side panels must be used whenever the sid...

TOOLS REQUIRED • Tinsnips to cut banding• Stepladder• Bucket• Level• Appliance Hand Truck• Tubing cutter• 7/16” open-end wrench• #2 Phillips screwdriver• Drill and appropriate bits• 5/16”, 7/16” socket • Safety glasses• 1-1/4” open end wrench• Pliers• 1/4” ratchet HARDWARE SUPPLIED • Water filter by...

STEP 2 INSTALL WATER LINE WARNING Connect to potable water supply only. AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. • A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 p.s.i. (275-827 kPa). • Route 1/4” ...

STEP 3 INSTALL SIDE PANELS Skip this step when not using side panels.If you are using 1/4” (0.63 cm) side panels, they should be inserted into the case trim. Fasten the panels to the refrigerator with stick-on hook and loop fastener strips before setting refrigerator in place. STEP 2A WATER LINE INS...

14 Installation Instructions - Standard Installation STEP 4 ANIT-TIP PROCEDURE (CONT) • Locate at least 2 studs on the back wall. Mark these points on the horizontal line. • Place the bottom of the wall bracket with tabs on the horizontal line. Align the center notch on the bracket with the center l...

STEP 5 LEVEL REFRIGERATOR All models have 4-point leveling. The front is supported by leveling legs, the rear is supported by adjustable wheels. Both are accessible from the front of the refrigerator.• To level the back of the refrigerator, turn the 7/16” hex nut located above the front wheels. Turn...

16 Installation Instructions - Standard Installation STEP 7 ALTERNATE ANTI-TIP PROCEDURE The refrigerator must be secured to prevent tipping . If the anti-tip bracket cannot be used, this alternate procedure may be used to secure the refrigerator against tip-over • Raise the grille panel to access c...

17 Installation Instructions - Standard Installation STEP 10 INSTALL 1/4” (0.63 cm)FRAMED PANELS Right hand models shown. Use the same instructions for left hand models.IF YOU ARE INSTALLING OVERLAY PANELS, GO TO STEP 10A. Install door and drawer panels: • Open door to 90°. Remove the 4 Phillips hea...

Installation Instructions - Standard Installation 14 STEP 10A INSTALL OVERLAY PANELS Custom handles If you are using custom handles, the handle must be properly secured to the panel before sliding the panel into the trim. • The cabinet manufacturer will supply the custom handle and hardware. • Secur...

STEP 12 CONNECT POWER • Check to be sure the power cord is plugged into the receptacle. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. • The temperature controls are preset at 37°F for the fresh food section and 0°F for the freezer. • ...

Installation Instructions - Standard Installation STEP 14 INSTALL TOEKICK • Locate the supplied toekicks (shipped taped to the side of the refrigerator. • The narrower set of toe kicks will be used with standard installation. You can discard the other set of toe kicks. • Install the toekick assembly...

THE INSTALLATION SPACE Water And Electrical Locations Electrical and water supply must be located as shown. The Cutout Depth Must Be 26-3/16” (66.52 cm) Wooden cleats are required for flush installation. See Side Cleats on page 27. Cutout depth beneath a soffit: When installed beneath a soffit, the ...

1/2” (1.27 cm) OVERLAY PANEL DIMENSIONS For a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel must be secured to a 1/4” (.63 cm) thick backer panel which slides into the trim. A spacer panel 0.10” (0.25 cm) thick must be placed between the overlay and bac...

24 Design Guide - Flush Installation 3/4” (1.9 cm) DECORATIVE PANEL DIMENSIONS For a more custom appearance, overlay panels may be installed to give a flush appearance with surrounding cabinets. The overlay panel must be 3/4” (1.9 cm) thick. Panel attaches to included brackets to provide mounting to...

28 Design Guide - Flush Installation SIDE PANELS Side panels must be used whenever the sides of the refrigerator will be exposed. The 1/4” (0.63 cm) side panels will slip into the side case trim. Secure the panels to the refrigerator with stick-on hook and loop fastener strips. Order the side panels...

TOOLS REQUIRED • Tinsnips to cut banding• Stepladder• Bucket• Level• Appliance Hand Truck• Tubing cutter• 7/16” open-end wrench• #2 Phillips screwdriver• Drill and appropriate bits• 5/16”, 7/16” socket • Safety glasses• 1-1/4” open end wrench• Pliers• 1/4” ratchet HARDWARE SUPPLIED • Water filter by...

STEP 2 INSTALL WATER LINE WARNING Connect to potable water supply only. AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement.• A cold water supply is required for automatic icemaker operation. The water pressure must be between 40 and 120 p.s.i. (275-827 kPa). • Route 1/4” O...

STEP 3 INSTALL SIDE PANELS Skip this step when not using side panels.If you are using 1/4” (0.63 cm) side panels, they should be inserted into the case trim. Fasten the panels to the refrigerator with stick-on hook and loop fastener strips before setting refrigerator in place. STEP 2A WATER LINE INS...

STEP 6 ALTERNATE ANTI-TIP PROCEDURE The refrigerator must be secured to prevent tipping. If the anti-tip bracket cannot be used, this alternate method can be used to prevent the unit from tipping. • Raise the grille panel to access case trim.• Use a 3/16” (0.47 cm) bit to drill four evenly spaced cl...

34 Installation Instructions - Flush Installation STEP 7 ADJUST DOOR SWING NOTE: This refrigerator has a 3-position door stop. When space does not allow the door to swing open fully to 115°, you may change the door swing to a 90° opening. Skip this step if door opening is satisfactory for your insta...

35 Installation Instructions - Flush Installation STEP 9 INSTALL DOOR PANELS Install door panel: • Open door to 90°. Remove the 4 Phillips head screws from the door handle. • Remove the handle. Retain all screws.• Remove the 4 screws holding the trim, then lift off the trim. Retain the screws. Custo...

STEP 11 CONNECT POWER • Check to be sure the power cord is plugged into the receptacle. • Check to make sure power to refrigerator is on by opening refrigerator door to see if interior lights are on. • The temperature controls are preset at 37°F (-13.89°C) for the fresh food section and 0°F (-17.78°...

Installation Instructions - Flush Installation STEP 13 INSTALL TOEKICK • Locate the supplied toekicks (shipped taped to the side of the refrigerator. • The wider set of toe kicks will be used for flush installation. You can discard the other set of toe kicks. • Attach the toekick assembly to the ref...

Instructions for Stainless Steel Installation 38 31-49142-1

THE INSTALLATION SPACE Water And Electrical Locations Electrical and water supply must be located as shown. The Cutout Depth Must Be 24” (60.96 cm) The refrigerator will project forward, slightly beyond adjacent cabinetry, depending on your installation. Allow minimum 1/8” (0.32 cm) air gap between ...

CUSTOMIZATION BASICS: Framed Or Overlay Panels, Custom Handles and Accessory Kits Professional Style Stainless Steel Refrigerators Stainless steel wrapped refrigerators with beveled edges and professional style handles. These models are shipped ready for installation. Stainless Steel Wrapped Refrige...

42 TOOLS REQUIRED • Tinsnips to cut banding• Stepladder• Bucket• Level• Appliance Hand Truck• Tubing cutter• 7/16” open-end wrench• #2 Phillips screwdriver• Drill and appropriate bits• 5/16”, 7/16” socket • Safety glasses• 1-1/4” open end wrench• Pliers• 1/4” ratchet HARDWARE SUPPLIED • Water filter...

STEP 8 ADJUST DOOR SWING NOTE: This refrigerator has a 3-position door stop. When space does not allow the door to swing open fully to 115°, you may change the door swing to a 90° opening. A 130° door swing is available for standard installation only. If used for flush installation, damage will occu...

STEP 9 CONNECT WATER SUPPLY WARNING Connect to potable water supply only. AVERTISSEMENT Raccordez l’appareil à une alimentation d’eau potable seulement. • Locate and bring tubing to the front of the cabinet.• Turn the water on to flush debris from line. Run about a quart of water through tubing into...

Installation Instructions - Stainless Steel Installation STEP 12 INSTALL TOEKICK • Locate the supplied toekick (shipped taped to the side of the refrigerator). Install the toekick assembly with the 2 screws provided, adjust to the desired height and tighten the screws. IMPORTANT: A custom toekick ca...