GE ZIR36N LH Manual - Free PDF Download

Page 2 - Contents; CAUTION

CAUTION Before you begin – Read these instructions completely and carefully. IMPORTANT – Save these instructions for local inspector ’s use. IMPORTANT – OBSERVE ALL GOVERNING CODES AND ORDINANCES. Note to Installer – Be sure to leave these instructions with the Consumer. Note to Consumer – Keep thes...

Page 3 - Design Information; Refrigerators, Freezers; Side Panel Requirements:; Advance Planning; DESIGN

3 Design Information 36 ″ Refrigerators, Freezers Flush orSemi-FlushEnclosureInstallations Side Panel Requirements: • Side panels are not required whenever the refrigerator is installed into an enclosure orbetween pantry and oven cabinets. • Side panels are required whenever the sides of the refrige...

Page 4 - • Electrical and water locations must; Freezer; Clearances; When Installed into a corner:

4 For a complete food storage center,install a Monogram Freezer andRefrigerator side by side. Order ZUG75Unified Grille Panel Kit for one continuous 3/4 ″ panel. • Electrical and water locations must be located as shown for either type of installation. A separate 115V, 60Hz. 20 amp power supply isre...

Page 5 - Side Panels. Leading; thick custom panels—Without trim kits; Refrigerator or Freezer

5 Installation At End-of-Run FramelessCabinets NOTE: 1/2 ″ thick side panels shown. Side panels can be anythickness. Add side panel thicknessto outside trim width, (36 ″ or 72 ″ for two models) to calculate therough-in dimension. The leading(front) edge must be finished tomatch surrounding cabinetry...

Page 7 - IMPORTANT; Optional Custom Trim Kits:; When installed into a corner:; Custom Panel Dimensions

7 ZIR36N RefrigeratorZIF36N Freezer Design Information Designed to be installed flush or semi-flush with surrounding cabinetry. Cutout dimensions,clearances and side panel sizes are determined bythe many installation options available. Side panelsmust be used whenever the sides of the refrigeratorwi...

Page 8 - Custom Door Panel Dimensions Using Standard Trim; thick panels; thick backing; Maximum total weight for; CUST

8 Custom Door Panel Dimensions Using Standard Trim 1/4 ″ thick panels or Panels secured to 1/4 ″ thick backing ZIR36N RefrigeratorZIF36N Freezer • 1/4 ″ Panel: Cut panels to size. • Custom handle with 1/4 ″ door panel requires Trim kits ZKHR1 or ZKHRSS1 for tubular stainless steelhandles. Standard T...

Page 9 - Custom Door Panel Dimensions; Using Trim Kits ZKTR36LH or ZKTR36RH; Custom Grille Panel; Maximum door panel weight is

9 ZIR36N RefrigeratorZIF36N Freezer • The ZKTR36LH (or ZKTR36RH) trim kit provides for the installation of 3/4 ″ thick custom door and grille panels, using the supplied handle. Cut panel to sizeand install. Custom Door Panel Dimensions Using Trim Kits ZKTR36LH or ZKTR36RH 3/4 ″ thick panel with kit ...

Page 10 - Using Trim Kit ZKTR36LH or ZKTR36RH; Installation Height

10 ZIR36N RefrigeratorZIF36N Freezer • The ZKTR36LH (or ZKTR36RH) trim kit installed together with a ZKHTR1 custom handle kit provides for the installation of 3/4 ″ thick custom door and grille panels with a custom handle of your choice.Order ZKHTRSS1 for a tubular stainless steel handle. Cut panels...

Page 11 - Trim; Side Panel or Filler Options; Top View

23 5/16" 84" 2 5/16" 24 3/4" 84" 3 3/4" 23 9/16" 84" 2 9/16" Trim 11 1/4 ″ Side Panels Insert end of side panel into trim.Use stick-on hook andloop fastener strips tosecure the panel tothe refrigerator. Standard 4 ″ high toekick or trim to fit . Height may vary de...

Page 12 - Flooring; Use of Extension Cords; Installation

12 ToolsRequired • Tinsnips to cut banding• Stepladder• 1-1/4 ″ open-end wrench • Bucket• Level• Appliance Hand Truck• Tubing cutter • 7/16 ″ open-end wrench • #2 Phillips screwdriver• Stubby Phillips screwdriver • Drill and appropriate bits • 7/16 ″ socket with 3 ″ extension for ratchet • Safety gl...

Page 13 - DO NOT ATTEMPT TO ROLL UNIT OFF SKID.; PRUDENCE; • Lift the refrigerator off the skid with an appliance

13 • Remove outer carton. – Carefully cut banding at the top and bottom. • Slide out back corner posts (2).• Slide carton off top of cabinet . NOTE: IT IS NOT NECESSARY TO LAY CABINET DOWN IN ORDER TO REMOVE SKID! • The unit is secured to the skid with 4 slotted tie- down straps. First remove the 5/...

Page 14 - Shut off the main water supply.; Floor

14 Step 2InstallWater Line • Install optional water filter in the water line near the refrigerator. A water filter is recommended in areaswhere water supply contains sand or particles.Installation instructions are packed with the filter. • A cold water supply is required for automatic icemaker opera...

Page 15 - When the refrigerator is installed; ATTENTION; WARNING

15 Step 3Install Side Panels • Side panels are not required when the refrigerator or freezer is installed into an enclosure. Skip thisstep if you are installing into an enclosure. • Side panels are required whenever the sides of the refrigerator or freezer will be exposed and wheninstalled between f...

Page 16 - GE SmartConnect; If you

16 Step 5LevelRefrigeratoror Freezer All models have 4-point leveling. The front is supportedby leveling legs, the rear is supported by wheels.• Adjust rear wheels beneath the product to just barely touch the 2x4 block. • Turn the 7/16 ″ hex nut located above the front wheels. Turn to raise or lower...

Page 17 - To insert custom grille panel into the frame:; gap

17 Step 9CheckPower • Check to make sure power is on by opening the door to see if interior lights are on. If you are using a 3/4 ″ thick custom panel, SKIP THIS STEP. See Dimensions and Specifications for grillepanel sizes. Order ZKTR36LH or ZKTR36RH and followthe installation instructions packed w...

Page 18 - • A standard toekick is supplied. Install with 2 screws; The vented toekick must remain; Door Hinge

18 Step 13StartIcemaker • A standard toekick is supplied. Install with 2 screws provided, adjust to desired height and tightenscrews. IMPORTANT: The vented toekick must remain unobstructed for proper air circulation and operation. Step 14Install Toekick Step 12Arrange Interior and SetTemperatureCont...

Page 19 - To change grille panel size:; min. gap between top of; ZGC2 Trim Kit; Grille Panel Frame Adjustment

19 This kit provides optional side trim pieces for the original grille panel frame to fit 83-1/2 ″ and 84-1/2 ″ installation heights. To change grille panel size: • Determine the installation height by measuring the enclosure from the floor to the underside of soffit .When there is no soffit , measu...

Page 20 - Support for Custom Handles

20 Tools and materials required:• #2 Phillips screwdriver• Drill and appropriate bits• Custom door panel• Custom Handle• Safety glasses Parts List: A. Handle side door extrusion (for left hand models)B. Handle side door extrusion (for right hand models) This kit provides the necessary framework to i...

Page 22 - Parts List; Kit Contents; Custom Panels

22 Right hand door swing models are illustrated in theseinstructions. Follow these instructions for left handmodels. Tools and materials required: • #2 Phillips screwdriver• Drill and appropriate bits • Custom door panels• Putty knife• Safety glasses• 7/16 ″ wrench Parts List A. Top trimB. Handle si...

Page 24 - Screws

24 Step 5Installhandles Step 6Adjustgrille panel height • Install new door handle using original screws. • Secure the grille panel support to the back side of the 3/4 ″ custom panel with #6 screws. • Be sure the lip of the support is over the top of the wood panel. Step 7Secure 3/4 ″ panel togrille ...

Page 26 - Tools and materials required:; This kit must be used in combination with; of your choice; Optimal final appearance depends on; Back Side

26 3/4 ″ custom door panel must be routed to accommodate these door handle extrusions. Routthe panel as illustrated, 1/4 ″ deep, and 1-13/16 ″ wide on the handle side. Refer to installation instructions for ZKTR36LH orZKTR36RH trim kit for 3/4 ″ custom panels: • Follow Step 1 to remove the standard ...

Page 27 - Screw

27 • Place the prepared 3/4 ″ custom door panel on the bottom trim with support bracket tabs inserted intotrim slots. • Push the panel back against the steel door, making sure the panel is flush with the hinge side trim. • Secure the panel to the trim temporarily by driving 2 screws through the back...

Page 29 - It is best that 2 people install this kit .; min. piece of plywood to; Tubular Stainless Steel Handles

29 Step 1Remove handle Right hand door swing models are illustrated in theseinstructions. Follow these instructions for left hand models. NOTE: It is best that 2 people install this kit . Tools and materials required: • #2 Phillips screwdriver• Drill and appropriate bits• Custom door panel• Safety g...

Page 30 - Step 2A

30 Step 2Matchhandle extrusionsto handle FOR CUSTOM WOOD PANELS See Step 2A for Stainless Steel panels • Cut a piece of corrugated to use as a pad to protect the panel finish. Use 1/2 ″ thick section of plywood to protect flooring when drilling. • Place custom panel on the pad, appearance side down....

Page 31 - FOR CUSTOM; • Slide panel into the door trim. Leave about 4

31 Step 3Installstandoffsonto handles • Place a handle standoff onto each attachment post along the handle. Position the set screw hole on thestandoff to point to the floor. • Install set screws into the bottom of each standoff, using the Allen wrench provided. The standoffshould be tight against th...

Page 32 - FOR; Panels have a protective plastic covering. Peel; Thick

32 Raised Panel on 1/4 ″ Thick Backing: A raised panel design secured to a 1/4 ″ thick backing (screwed or glued) can be used with this handle kit .• Cut the 1/4 ″ thick panels to size. • Fabricate the raised panel to allow 1-1/4 ″ clearance from the hinge side of the panel to avoidstriking adjacent...

Page 35 - Tools and materials Required:; ZUG75 Trim Kit; Custom Grille Panel Kit

35 This kit provides for the installation of a 3/4 ″ thick custom grille panel to span the combined width of a side by side installation. Use this kit in combination with 3/4 ″ custom panel kits, ZKTR36LH and ZKTR36RH. Tools and materials Required: • #1 and #2 Phillips screwdrivers or sockets• 1/4 ″...

Page 40 - For Monogram; wrench to turn the hinge.; GE Consumer & Industrial

Pub. No. 49-60055-4Dwg. No. 197D2785P001 08-07 JR NOTE: While performing installations described in this book, safety glasses or goggles should be worn. For Monogram ® local service in your area, call 1.800.444.1845. NOTE: Product improvement is a continuing endeavor at General Electric. Therefore, ...