GE 45129 Manual - Free PDF Download

Page 2 - Table of Contents

Important Safeguards 3 Designing a system 4 Controls, Indicators, and Features 5 Battery Backup - Control Center 5 Low Battery Indicators ( Control Center & Sensors) 6 The Choice Alert Operating Modes 6 Notification Mode 6 Dedicated Alert Mode (Zone 4) 7 Armed/Alarm Modes 7 Mute Function 7 Place...

Page 3 - Congratulations

Before connecting or operating the Control Center, please read these instructions carefully and save this manual for future reference. Congratulations The GE Choice Alert ™ Wireless Alarm System is one of the most affordable and expandable wireless alarm systems available. You’ll discover that the s...

Page 4 - – a maximum; Clean sheet of paper, ruler and pencil with; Window/Door Sensor

4 5 you’re concerned about the hot water tank or the dishwasher leaking? This system will help alleviate those concerns. To start, sketch a map of areas in and around your home and determine which doors and/or windows need contact Sensors, which areas that might best be served by a Motion Sensor, et...

Page 5 - Arm; Front; Notification

4 5 Control, Indicators, and Features: Zone Indicators These LEDs indicate Sensor status for each of the 4 Zones in the Choice Alert system. Armed and Power Indicators These LEDs indicate status of the system. Keypad Operations: Arm butto n - Use this button on the keypad to select the arm setting (...

Page 6 - The Choice Alert System operates in

6 7 of the arrow. Install batteries according to the battery polarity diagram inside the battery compartment. Replace the battery door. Note: The Control Center has an automatic internal battery tester. After batteries are installed you can check the backup battery status at any time by unplugging t...

Page 7 - Mute –

6 7 Notification switch settings: Off – In this mode when a Sensor is activated, the Control Center will issue a visual Alert only (flashing Zone LED indicator), no audio will be heard. The LED indicator will continue to flash as long as the Sensor is activated (door or window is open, garage door i...

Page 8 - Bypass –; When setting the Security Code you have 15 seconds to

8 1 2 3 4 Arm Zone Armed Power 1 2 3 4 Alert Chime Off Mute Learn Input DC 12V - + To create a new Security Code Step 1Press and hold the Learn button, Then press and hold the Arm button together for three seconds Step 2Enter the current code Step 4Re- Enter new code to confirm Step 3Enter new code ...

Page 9 - Sensors and Zones

8 1 2 3 4 Arm Zone Armed Power 1 2 3 4 Alert Chime Off Mute Learn Input DC 12V - + Zone 4 Continuosly Monitorsany area, in and aroundthe home, using any combination of the four Sensors Note: Zone 4 is not affected by Notification mode switch, and does not activate alarm Deticated Alert Zone (Zone 4)...

Page 10 - Here are Some examples of possible; Garage door Sensor; Assigning a Sensor to a Zone; Step 1 –

0 1 2 3 4 Arm Zone Armed Power 1 2 3 4 Alert Chime Off Mute Learn Input DC 12V - + Step 1Press and hold the Learn button for three seconds Step 3Activate the Sensor Step 2Select the Zone number open, storage sheds or work shops unsecured, etc). Sensors placed in Zone 4 will not activate the Alarm or...

Page 11 - Erasing a Sensor from a Zone

0 Step 2 – Press the Zone button (1, 2, 3 or 4) for the Zone you want to assign to the Sensor. The LED indicator for that Zone will begin to flash. Step 3 – Release the Zone button. Note: Zone 4 is for dedicated alerts only. Sensors in this Zone will not trigger an alarm or chime. Step 4 – Activate ...

Page 12 - To set the system in HOME mode; To set system in AWAY mode; Enter your four digit Security Code.; If a Sensor is triggered in Zone 4 it will not activate the; Disarming the System

1 2 3 4 Arm Zone Armed Power 1 2 3 4 Alert Chime Off Mute Learn Input DC 12V - + AWAY Mode To set the Alarm in Away Mode Step 1Enter four digit Security CodeStep 2Press “ Arm ” button twice The Armed LED indicatorbegins flashing (45 seconds to exit) Step 3To disarm, enter the four digit Security Cod...

Page 13 - Adding a Silent AlertTM; Even if the Control Center is disconnected from power or

Bypass a Zone (For all Zones and Modes) There may be occasions when you would like to temporarily prevent the Sensors in a Zone from triggering the alarm. In this situation you can bypass a Zone when setting the alarm. Once the alarm is disarmed the Bypass setting will be removed. Step 1 - Select th...

Page 14 - Step 3; Test the Alarm Siren; Adding a Signal Repeater; Sensor

4 5 Test the Silent Alert Step 1 - After the Silent Alert has been successfully linked with the Control Center, press and hold the Mute button on the Control Center for three seconds. This action sends a test signal. Step 2 - When the Silent Alert receives the test signal from the Control Center, on...

Page 15 - This process will help you locate the Signal Repeater

4 5 Step 2 - When the Control Center receives the Signal Repeater’s test signal, it will flash the green power indicator. This means a confirmation signal was sent back to the Signal Repeater. Release all buttons. Step 3 - When the Signal Repeater receives the confirmation signal, the LED indicator ...

Page 18 - FCC Warning; Description; *maximum potential life based upon usage and location

8 FCC Warning Any unauthorized changes or modifications to the equipment would void the user’s warranty and may conflict with both state and federal laws. The Choice Alert system complies with part 15 of the FCC rules. Operation is subject to the following conditions: ) The Choice Alert system may n...

Page 20 - WARNING

is a trademark of the General Electric Company and is used under license to Jasco Products Company LLC, 10 E. Memorial Road, Oklahoma City, OK 73114. This Jasco product comes with a 1 year limited warranty. Visit www.jascoproducts.com for details. 45129-1 11/02/07 WARNING Limitations of Alarm Produc...