Page 2 - COMPONENTS REQUIRED; TOOLS; Supplied
2 COMPONENTS REQUIRED TOOLS PARTS Supplied F 6mm Allen key F Spanner (washer) F Spanner (plinth) Not supplied F Box cutter F Phillips screwdriver F Level Supplied and required F 4x M10 bolts F 2x plinth bolt hole covers F 4x short stacking kit screws F 2x long stacking kit screws Supplied and to be ...
Page 3 - ACCESSING YOUR PRODUCT SPECIFICATIONS
3 ACCESSING YOUR PRODUCT SPECIFICATIONS For full product, cabinetry and service specifications, refer to the Planning Guide. To access the Planning Guide, scan the QR code or visit fisherpaykel.com/specify. Search by appliance type, product name or model code. 1220 1260 1900 700 1920 700
Page 4 - PRIOR TO INSTALLATION; Ensure power will remain
4 PRIOR TO INSTALLATION 3. Ensure power will remain accessible following install to allow access for any future product maintenance.Service holes should be smooth with gromets installed where required.Refer to the services section of the Planning Guide for more details. 2. Ensure floor is level and ...
Page 5 - UNPACK ALL PRODUCTS; Ensure accessories are
5 UNPACK ALL PRODUCTS Washer and Dryer: Cut the straps and the line printed on the top of the carton. Lift to remove. Discard braces and corner posts. Remove any packaging and accessories from the drum and base packer. Dispose of packaging responsibly. Fabric Care Cabinet: Cut the straps and the lin...
Page 7 - Push the front of the plinth; LEVEL PLINTH; Place the plinth in its final
7 1. Push the front of the plinth to open. Remove the divider before closing the drawer. LEVEL PLINTH 2. Place the plinth in its final install location. Adjust the feet using the supplied spanner until the washer is level front to back and corner to corner. 3. Using the spanner provided, tighten the...
Page 8 - FIT WASHER TO PLINTH
8 1. Tilt the washer back onto a protected surface such as the plinth carton. Ensure cords and hoses are not crushed. For new products, we recommend keeping the transit bolts fitted during this step. 2. Unwind feet using the supplied spanner to remove. 3. Partially fit the four M10 bolts supplied wi...
Page 11 - REMOVE WASHER TRANSIT BOLTS
11 1. Using the supplied spanner, remove all four transit bolts from the back of the washer. 2. Pull the rubber grommets and spacers outwards to remove. 3. Using a Phillips screwdriver, remove the two side brackets. REMOVE WASHER TRANSIT BOLTS
Page 13 - INSTALL STACKING KIT TO WASHER; Align the front corner of the
13 INSTALL STACKING KIT TO WASHER 1. Align the front corner of the stacking kit to the washer. 2. Secure the stacking kit to the washer using the four supplied short screws in the marked locations. If using a drill, the lowest torque setting is recommended.
Page 14 - INSTALL DRYER TO STACKING KIT; Ensure stacking kit shelf is
14 INSTALL DRYER TO STACKING KIT 1. Ensure stacking kit shelf is pushed all the way in and dryer feet have been fully wound in. 2. Lift dryer onto the stacking kit ensuring all four feet rest in the slots. 3. Using the two supplied long screws, secure the dryer to the stacking kit at the rear.
Page 15 - Remove the two screws from
15 INSTALL DRYER TO STACKING KIT 4. Remove the two screws from the front of the dryer and refit through the stacking kit.
Page 16 - LEVEL PRODUCT SET; We recommend levelling and
16 LEVEL PRODUCT SET 1. We recommend levelling and installing stacked products into alcove before fabric care cabinet. 2. Partially roll stacked products into alcove and check alignment. To do this, use the supplied 6mm hex key, rotate clockwise to lower both sets of wheels via the adjustment screws...
Page 17 - Using the supplied 6mm hex
17 LEVEL PRODUCT SET 4. Using the supplied 6mm hex key, rotate counter-clockwise to raise both sets of wheels via the adjustment screws.
Page 18 - CONNECT CABLES AND HOSES; Refer to the Planning Guide
18 CONNECT CABLES AND HOSES 1. Refer to the Planning Guide for service information. 2. Optional: For displayed dryers, fit the drain hose extension if dryer can be plumbed. 3. Display-free models:Display-free models must be plumbed. Unwind the drain hose. Plumbed installations: Ensure hose can be co...
Page 19 - Remove caps from washer
19 CONNECT CABLES AND HOSES 4. Remove caps from washer and dryer before fitting one of the communication cables.Connect the washer and dryer via the communication cable. 5. Connect fabric care cabinet communication cable to dryer. 6. Connect the angled end of the cold water hose (supplied with washe...
Page 20 - Connect the angled end of
20 CONNECT CABLES AND HOSES 7. Connect the angled end of the short hose (supplied with dryer) to the cold water inlet on the washer. 8. Connect both hoses to the top of the Y join supplied with the dryer. 9. Connect the straight hose to the bottom of the Y join.
Page 22 - Install the drain hose guide
22 CONNECT CABLES AND HOSES 13. Install the drain hose guide to the back wall.Refer to the planning guide for placement details. 14A. Standpipe Installations: Route the drain hose through the guide and place into the standpipe.Ensure a maximum of 20mm of the hose rests in the standpipe. 14B. Spigot ...
Page 23 - Roll products into the
23 15. Connect hoses to taps before turning on. Check for leaks at all connection points. 16. Connect the power cables and check products are powered on and are connected. CONNECT CABLES AND HOSES 17. Roll products into the alcove. Take care not to damage hoses or cords.
Page 24 - Check alignment and
24 CONNECT CABLES AND HOSES 19. Check alignment and ensure required clearances are maintained. Adjust as required. 20. Once adjustment is complete, fit the plinth bolt hole covers. 18. Turn the adjustment screw counter-clockwise to retract the wheels. Ensure the wheels are fully raised off the floor...
Page 25 - INSTALL FABRIC CARE CABINET; Open the cabinet door and
25 INSTALL FABRIC CARE CABINET 1. Open the cabinet door and lower the rear wheel using the supplied Allen key. Rotate clockwise to lower the wheel and counter-clockwise to raise. 2. When adjusting the wheel, ensure front of the door doesn’t damage the floor. 3. Prior to installing in alcove, adjust ...
Page 26 - Tighten the locking nuts up
26 INSTALL FABRIC CARE CABINET 4. Tighten the locking nuts up to the base of the cabinet to lock feet in position. 5. Lower the rear wheel to achieve clearance between rear feet and floor. When adjusting the wheel, ensure front of the door doesn’t damage the floor. 6. Connect communication and power...
Page 27 - Push cabinet into cavity
27 INSTALL FABRIC CARE CABINET 7. Push cabinet into cavity taking care not to damage cords.Rotate the rear wheel adjustment screw anti-clockwise to place the full cabinet weight onto feet.Ensure rear corners are level and set to the desired height. 8. With cabinet in the final position, unscrew fron...
Page 28 - Check final alignment and
28 INSTALL FABRIC CARE CABINET 10. Check final alignment and ensure required clearances are maintained. Adjust as required. 11. Clip drip tray into position. 9. Ensure cabinet is resting on all four feet and all wheels have been raised.
Page 29 - Complete and keep for safe reference:; INSTALLER CHECKLIST
29 Complete and keep for safe reference: Model Serial no. Purchase date Purchaser Dealer address Installer’s name Installer’s signature Installation company Installation date INSTALLER CHECKLIST
