Page 2 - PRODUCT LABEL
2 Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. Theywill also provide a means by which to make full use ofthe features offered by your appliance. Please kee...
Page 3 - IMPORTANT PRECAUTIONS AND RECOMMENDATIONS; After use, ensure that the knobs are in off position.
3 IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FORUSE OF ELECTRICAL APPLIANCES Use of any electrical appliance implies the necessity to follow a series of fundamentalrules. In particular: ■ Never touch the appliance with wet hands or feet; ■ do not operate the appliance barefooted; ■ do not allow child...
Page 4 - min; Figure 1; General Dimensions; Width; INSTALLATION; This appliance shall only be serviced by authorized personnel.
4 470 35 min 500 550 100 580 min Figure 1 DIMENSIONS (Table 2): (Note: Also refer to Figure 1) General Dimensions Width 580 mm Depth 500 mm Depth Below Mounting Surface 30 mm Cut-out Dimensions Width 550 mm Depth 470 mm INSTALLATION CAUTION: ■ This appliance must be installed in accordance with thes...
Page 5 - Figure 2; General Requirements for Domestic electrical appliances
5 750 mm 35 mm min 100 mm min 500 mm 450 mm Figure 2 CLEARANCES: Installation clearances and protection of combustible surfaces shall comply with thecurrent local regulations e.g. AG 601 (AS 5601) - Gas Installations code. This cooktop has been designed and constructed in accordance with the followi...
Page 6 - Figure 3
6 The installation shall comply with the dimensions in Figures 1 and 2, bearing in mindthat: ■ A minimum clearance of 20 mm has to be kept between the bottom of the cooking hob and the top of an appliance or a shelf. To ensure this clearancemount the spacers, supplied with the appliance, as shown in...
Page 7 - ing care to overlap the gasket at the corners.; Figure 4
7 INSTALLATION (Refer to Figure 4): 1. Spread out the gasket “C” over the workbench at the edge of the cut out tak- ing care to overlap the gasket at the corners. 2. Slot in the cooking hob into the cut out of the workbench and locate it cor- rectly. 3. Adjust the clamps “A” and tighten the screws “...
Page 8 - Warning; : Do not use any naked flame to check for leaks.; Figure 5b; Gas connection for
8 GAS SUPPLY: ■ This appliance is suitable for use with Natural Gas or ULPG. (Check the “gas type”sticker attached to the appliance). ■ For Natural Gas the gas supply must be regulated to obtain a pressure of 1 kPa with the two semi-rapid (SR) burners operating. ■ For ULPG models connect the gas sup...
Page 9 - TABLE FOR THE CHOICE OF THE INJECTORS; Natural gas; INSTALLATION WITH A FLEXIBLE HOSE ASSEMBLY; IMPORTANT WARNING; : The installer shall ensure the hose assembly is restrained
9 TABLE FOR THE CHOICE OF THE INJECTORS Natural gas ULPG Test Point Pressure [kPa] 1.0 2.75 BURNER Auxiliary (A) 0.85 3.6 0.53 3.6 Medium-speed burner (SR) 1.12 6.3 0.70 6.3 Triple-ring burner (TR) 1.55 11.9 0.94 11.9 Gas Consumption [MJ/h] Injector Orifice Dia. [mm] Gas Consumption [MJ/h] Injector ...
Page 10 - CONVERSION PROCEDURE; REPLACING THE INJECTORS; To replace the injectors proceed as follows:; IMPORTANT; Figure 6
10 CONVERSION PROCEDURE (to convert to Natural gas or to ULPG) REPLACING THE INJECTORS The conversion procedure must be carried out only by an authorised person. This appliance is suitable for use with Natural gas or ULPG (check the “gas type” stick-er attached to the appliance). The nominal gas con...
Page 11 - MINIMUM BURNER SETTING ADJUSTMENT; using a screwdriver turn screw; Normally for ULPG, fully tighten the adjustment screw.; LUBRICATING THE GAS TAP; Figure 8
11 MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spreads to all burner ports when the burner is lit with thegas tap set to the minimum position. If some ports do not light, increase the minimumgas rate setting. Check whether the burner remains lit even when the gas tap is turned quickly ...
Page 12 - ELECTRICAL REQUIREMENTS:; THIS APPLIANCE MUST BE EARTHED.; ELECTRIC DIAGRAM KEY
12 ELECTRICAL REQUIREMENTS: WARNING: ■ THIS APPLIANCE MUST BE EARTHED. CAUTION: ■ Ensure that the power outlet is properly earthed before connecting the appliance. ■ Disconnect power before servicing the appliance. The appliance is provided with a standard 240VAC three pin plug and powercable (3 x 0...
Page 13 - USE and CARE
13 USE and CARE CAUTION: ■ This appliance must be used only for the task it has explicitly been designed for, that is for domestic cooking of foodstuffs. Any other form of usage is to be con-sidered as inappropriate and therefore dangerous. Do not use this appliance asa space heater. ■ Do NOT place ...
Page 14 - CONTROL PANEL; GAS HOB; GAS BURNERS; This appliance is class 3
14 ■ The electric ignition is incorporated in the knobs ■ This appliance is class 3 2 8 7 6 5 3 4 1 CONTROL PANEL 5 . Triple-ring burner control knob (1) 6 . Left semi-rapid burner control knob (2) 7 . Right semi-rapid burner control knob (3) 8 . Auxiliary burner control knob (4) Figure 11a 2 8 7 6 ...
Page 15 - LIGHTING GAS BURNERS
15 LIGHTING GAS BURNERS ■ Check that the electricity is switched on to allow spark ignition. ■ Make sure that all controls are turned to zero. ■ The gas flow to the burner is controlled by the knobs on the safety taps. ■ You control the flow by turning the knob indicator to line up with the followin...
Page 16 - Important; wait for at
16 Lighting the burnersWITH ELECTRIC IGNITION (without safety cut-off valve) mod. DEGH60WT - DEGH60ST To light one of the burners, press and turn the corresponding knob to the maximumflow position (large flame) and keep the knob pressed down until the gas is lit. Turn the gas tap to the position req...
Page 17 - DO NOT
17 COOKING HINTS FOR GAS HOBS Burners Pan diameter Auxiliary * 12 - 14 cm Semi-rapid 16 - 20 cm Triple ring 24 - 28 cm Wok max 36 cm The burner must be chosen according to the diameter of the pans and energyrequired. For optimum efficiency use a wok or pan no smaller than 230mm diameter. Saucepans w...
Page 18 - CORRECT USE OF TRIPLE-RING BURNER; To use the WOK, you must place the wok stand in the; CORRECT; position as; MUST BE PLACED ONLY; WRONG
18 mod. DEGH60WT - DEGH60ST Figure 15a CORRECT USE OF TRIPLE-RING BURNER ■ The flat-bottomed pans are to be placed directly onto the pan-support. ■ To use the WOK, you must place the wok stand in the CORRECT position as shown in fig. 15a - 15b. IMPORTANT: The special grille for wok pans (figs. 15a, ...
Page 19 - Cleaning and Maintenance; GENERAL TIPS; Note; BURNERS AND GRIDS
19 Cleaning and Maintenance GENERAL TIPS ■ Before cleaning the hob switch it off and wait for it to cool down. ■ Clean with a cloth, hot water and soap or liquid detergent. ■ Do not use products which are abrasive, corrosive or chlorine based. ■ Do not use steel pads. ■ Do not leave acid or alkaline...
Page 20 - CORRECT POSITIONING OF THE BURNERS; Model DEGH60 only; GAS TAPS
20 Figure 16 Figure 17 CORRECT POSITIONING OF THE BURNERS ■ It is very important to check that spreader F and cap C of the burner (see Figures 16 and 17) are perfectly in place because if they move out of placeserious problems could arise. ■ Make sure that electrode S (Fig. 16) is kept clean so that...
Page 21 - CORRECT POSITIONING OF THE TRIPLE-RING BURNER; Then position the cap
21 CORRECT POSITIONING OF THE TRIPLE-RING BURNER ■ The triple ring burner must be correctly positioned (see fig. 20); the burner rib must be located in position as shown by the arrow (see fig. 18). ■ The burner correctly positioned must not rotate (fig. 19). ■ Then position the cap A and the ring B ...
Page 22 - SERVICE AND MAINTENANCE; Servicing the appliance:
22 SERVICE AND MAINTENANCE If the ignition spark fails to ignite or does not light the gas, check the followingitems before calling our Customer Service Centre to obtain the nearest AuthorisedDelonghi Service Agent: ■ Burner is reassembled and located correctly. ■ Spark electrode and white ceramic a...
