Page 2 - PRODUCT LABEL
2 Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. Theywill also provide a means by which to make full use ofthe features offered by your appliance. Please kee...
Page 3 - IMPORTANT PRECAUTIONS AND RECOMMENDATIONS; After use, ensure that the knobs are in off position.
3 IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FORUSE OF ELECTRICAL APPLIANCES Use of any electrical appliance implies the necessity to follow a series of fundamentalrules. In particular: ■ Never touch the appliance with wet hands or feet; ■ do not operate the appliance barefooted; ■ do not allow child...
Page 4 - INSTALLATION; appliance; ELECTRICAL REQUIREMENTS; suitable for the power consumed by the appliance.
4 INSTALLATION CAUTION: ■ This appliance must be installed in accordance with these installationinstructions, local gas fitting regulations, municipal building codes,water supply regulations, electrical wiring regulations, AS5601 / AG 601- Gas Installations and ony other relevant statutory regulatio...
Page 5 - Figure 1; BURNER COOKING HOB; Figure 2
N.B. The connection of the appliance to earth is mandatory. If the installation requires alterations to the domestic electrical system call a qualifiedelectrician. He should also check that the socket cable section is suitable for the power drawnby the appliance. Replacing the power cord must be don...
Page 6 - Figure 3; General Dimensions; Width
6 Figure 3 CLEARANCES: Installation clearances and protection of combustible surfaces shall comply with thecurrent local regulations e.g. AG 601 (AS 5601) - Gas Installations code. DIMENSIONS: (Note: Also refer to Figure 3) General Dimensions Width 288 mm Depth 510 mm Depth Below Mounting Surface 30...
Page 7 - minimum clearance; has to be; partition; between the; should; Figure 4; adhesive tape; Figure 5
7 750 mm 50 mm min 100 mm min 500 mm 450 mm The installation shall complywith the dimensions in Figures3 and 4, bearing in mind that: ■ A minimum clearance of 20 mm has to be kept between the bottomof the cooking hob andthe top of an applianceor a shelf. To ensure this clear-ance mount the spac-ers ...
Page 8 - FASTENING THE COOKTOP; Side clearances; - Where the dimensions from the periphery of the nearest; Protection of combustible surfaces; - Local regulations in force specifies; Figure 6; Take care not to
A A A A FASTENING THE COOKTOP (fig. 6) Each cooktop is supplied with a set oftabs and screws to fasten it on unitswith a working surface from 2 to 4 cmdeep. The kit includes 4 tabs “A” and 4 self-threading screws “B”. ■ Cut the unit. ■ Stretch gasket “D” over the edge ofthe hole made, being careful ...
Page 9 - Figure 9; Gas connection for
GAS SUPPLY: ■ This appliance is suitable for use with Natural Gas or ULPG . (Check the “gas type” sticker attached to the appliance). ■ For Natural Gas the gas supply must be regulated to obtain a pressure of 1 kPa with the two largest burners operating. ■ For ULPG models connect the gas supply dire...
Page 10 - INSTALLATION WITH A FLEXIBLE HOSE ASSEMBLY
5. Check the minimum burner setting by quickly rotating the gas control knob from the maximum to the minimum position, the flame must not go out. If adjust-ment is required carry out the “minimum burner setting adjustment" proceduredescribed below. 6. If satisfactory performance cannot be obtain...
Page 11 - TABLE FOR THE CHOICE OF THE INJECTORS; Natural Gas; Burner
(Note: Gas type sticker and data plate are attached to the underside of the base ofthe appliance.) TABLE FOR THE CHOICE OF THE INJECTORS Natural Gas ULPG Test Point 1.0 2.75 Pressure (kPa) Burner Injector Orifice Gas Consumption Injector Orifice Gas Consumption [mm] [MJ/h] [mm] [MJ/h] Semi-rapid 1.1...
Page 12 - REPLACING THE INJECTORS; To replace the injectors proceed as follows:; IMPORTANT
J J Figure 11 Figure 12 12 CONVERSION PROCEDURE (to convert to Natural gas or toULPG) REPLACING THE INJECTORS The conversion procedure must be carried out only by an authorised person. This appliance is suitable for use with Natural gas or Universal LPG (check the “gastype” sticker attached to the a...
Page 13 - MINIMUM BURNER SETTING ADJUSTMENT; Normally for; LUBRICATING THE GAS TAP
A Figure 13 Figure 14 13 MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spreads to all burner ports when the burner is lit withthe gas tap set to the minimum position. If some ports do not light, increase theminimum gas rate setting. Check whether the burner remains lit even when the gas ...
Page 14 - USE and CARE; “1 BURNER COOKING HOB”; COOKING POINT; Triple ring burner control knob; “2 BURNER COOKING HOB”; The appliance is class 3 rated; COOKING POINTS
USE and CARE CAUTION: ■ This appliance must be used only for the task it has explicitly been designed for, that is for domestic cooking of foodstuffs. Any other form of usage is tobe considered as inappropriate and therefore dangerous. Do not use thisappliance as a space heater. ■ Do NOT place combu...
Page 15 - LIGHTING GAS BURNERS; Check that the electricity is switched on to allow spark ignition.
LIGHTING GAS BURNERS ■ Check that the electricity is switched on to allow spark ignition. ■ Make sure that all controls are turned to zero. ■ The gas flow to the burner is controlled by a tap incorporating a safety cut-offvalve. If the burner flame should go out for some reason, the safetyvalve will...
Page 16 - – Adjust the gas valve to the desired position.
LIGHTING GAS BURNERS (FITTED WITH SAFETY CUT-OFF VALVE) In order to light the burner, you must: 1 – Turn the knob fig. 18 in anti-clockwise direction up to the maximum aperture, push in and hold the knob; this will light the gas. If there is no mains electricalsupply, bring a lighted match close to ...
Page 17 - WRONG; CORRECT USE OF TRIPLE-RING BURNER; CORRECT; COOKING HINTS FOR GAS HOBS
Burners Pan diameter Semirapid (SR) 12 to 20 cm Rapid (R) 22 to 26 cm Triple ring 24 to 28 cm WRONG CORRECT CORRECT USE OF TRIPLE-RING BURNER ■ The flat-bottomed pans are to be placed directly onto the pan-support. ■ To use the WOK you must place the wok stand in the CORRECT position as shown in fig...
Page 18 - Before you begin cleaning, you must ensure that the appliance is; the enamelled parts.; Cleaning and Maintenance; These parts can be removed and cleaned with appropriate products.
GENERAL ADVICE ■ Before you begin cleaning, you must ensure that the appliance is switched off. ■ It is advisable to clean when the appliance is cold and especially when cleaning the enamelled parts. ■ Avoid leaving alkaline or acidic substances (lemon juice, vinegar, etc.) on the sur- faces. ■ Avoi...
Page 19 - CORRECT REPLACEMENT OF THE BURNERS; Both the probe and ignition plug must be very carefully cleaned.
Figure 23 Figure 22 Figure 24 CORRECT REPLACEMENT OF THE BURNERS It is very important to check that the burner flame distributor F and the cap C hasbeen correctly positioned (see figs. 22 and 26) failure to do so can cause seriousproblems.Check that the electrode “S” (fig. 22) is always clean to ens...
Page 20 - TRIPLE RING BURNER
TRIPLE RING BURNER The triple ring burner must be correctly positioned (see fig. 23); the burner ribmust be located in position as shown by the arrow. Then position the cap A and the ring B (fig. 24 - 25).The burner correctly positioned must not rotate (fig.24). Figure 25 Figure 26 20
Page 21 - SERVICE AND MAINTENANCE
21 SERVICE AND MAINTENANCE If the ignition spark fails to ignite or does not light the gas, check the followingitems before calling our Customer Service Centre to obtain the nearest AuthorisedService Agent: ■ Burner is reassembled and located correctly. ■ Spark electrode and white ceramic are clean ...
