Page 2 - CONTENTS
2 CONTENTS Contents: Welcome ..............................................................................2 Warranty registration ..........................................................2 Safety information ...............................................................3 Unpacking your appliance ...
Page 3 - Recognize Safety Symbols,; Important Safety Instructions; SAFETY INFORMATION AND UNPACKING YOUR APPLIANCE
3 NOTE NOTE ! CAUTION Recognize Safety Symbols, Words, and Labels. CAUTION- Hazards or unsafe practices which could result in personal injury or property / product damage. NOTE- Important information to help assure a problem free installation and operation. DCS is committed to building a quality pro...
Page 4 - INSTALLING YOUR APPLIANCE; WARNING
4 ! CAUTION Cabinet Clearance Ventilation is required from the bottom front of the appliance. Keep this area open and clear of any obstructions. Adjacent cabinets and counter top can be installed around the appliance as long as the front grille remains unobstructed. Overlay door models with articula...
Page 5 - NOTE; Electrical Shock Hazard; Electrical Connection; Model
5 NOTE Figure 2 Figure 3 Do not remove ground prong INSTALLING YOUR APPLIANCE Front grille Front grille screw Figure 4 Electrical Shock Hazard • Do not use an extension cord with this appliance. They can be hazardous and can degrade product performance. • This appliance should not, under any circums...
Page 6 - INSTALLING THE DRAIN PLUMBING; CL; Drain Plumbing; CAUTION
6 INSTALLING THE DRAIN PLUMBING Access panel Drain pipe, (not provided) Drain tubing, cut to length and install in the drain CL CL 14 7 ⁄ 8 " (37.8 cm) 11 ⁄ 16 " (17mm) 1 1 ⁄ 4 " (3.2 cm) 4 17 ⁄ 32 " (11.5 cm) 21 1 ⁄ 2 " (54.6 cm) Figure 8 Figure 7 Drain line coiled and secured t...
Page 8 - INSTALLING THE WATER SUPPLY; Water Supply; TYPE VALVE IS NOT RECOMMENDED
8 Reverse osmosis, (RO), water, softened water, and de- ionized water are not recommended as they can adversely affect the quality and quantity of the ice. Water Supply Line Clamp and Screw Figure 1 0 Back view of ice machine NOTE ! CAUTION INSTALLING THE WATER SUPPLY Compression fitting Water suppl...
Page 9 - Procedure for Testing Drain System; ICE
9 INSTALLING THE WATER SUPPLY Procedure for Testing Drain System (both gravity and drain pump models) Drain pump models have a safety feature that will interrupt power to the unit if a high-limit condition occurs to prevent flooding. This safety feature can be initiated by a restriction in the drain...
Page 10 - The Ice Making Process; OPERATION OF THE ICE MACHINE
10 The Ice Making Process Your ice machine is unique in how it forms ice with fractional freezing to form a slab of ice that is clear and has less dissolved solids than the water it is produced from. This is accomplished by running water over the cold evaporator plate (see Figure 1 4 ) which gradual...
Page 11 - OPERATION OF ICE MACHINE
11 The bin level sensor is located in the ice bin, it senses when the ice supply is low or full and starts or stops the ice making process accordingly. If the water supply is turned off to the ice machine be sure to set the electronic control to the “OFF” position or remove power to the unit. New So...
Page 12 - PRODUCT DIMENSIONS
12 PRODUCT DIMENSIONS ROUGH-IN OPENING DIMENSIONS CABINET DIMENSIONS MODEL "A" "B" "C" "D" "E" "F" "G" "H" "J" RF15I 15" 34" to 35" 24" 14 7 ⁄ 8 " 33 3 ⁄ 4 " to 34 3 ⁄ 4 " 23 5 ⁄ 8 " 27 7 ⁄ 32 ...
Page 14 - USING YOUR ELECTRONIC CONTROL; Starting your clear ice machine:
14 USING YOUR ELECTRONIC CONTROL Starting your clear ice machine: Plug the ice machine into a 115 volt wall outlet, (see page 5 for electrical information). Your appliance is shipped from the factory in the "ICE" mode and will begin start-up of ice production after the start-up routine. Upon...
Page 15 - Turning your ice machine On and Off:
15 Turning your ice machine On and Off: If your appliance is on, "ICE" will be displayed. To turn the appliance off, push and hold the "ON/ OFF" icon for 3-seconds. The display will show "OFF" . The drain pump (if equipped) and the interior light will still be functioning dur...
Page 17 - CLEANING YOUR ICE MACHINE; CLEAN; Once you have your cleaner:; Do not try to remove ice that is embedded in; OFF
17 CLEANING YOUR ICE MACHINE ! CAUTION Forcing ice through the grid cutter will break the grid cutter wires. ! CAUTION Remove all ice from the evaporator plate and grid cutter area that is not embedded in wires Figure 2 2 Figure 2 3 Clean mode: To ensure maximum performance and ice quality, it is re...
Page 20 - CARE AND CLEANING; Canceling clean mode:
20 CARE AND CLEANING Optional: After the cleaning cycle has been completed , you may wash the interior with a mild detergent / dish soap or a solution of two tablespoons of baking soda and one quart of water. Rinse with clean water. Replace the grid cutter cover. After cleaning it is recommended you...
Page 21 - Electrocution Hazard; TROUBLESHOOTING THE ICE MACHINE; Before You Call for Service; Ice Production
2 1 • Never attempt to repair or perform maintenance on the appliance until the main electrical power has been disconnected. Turning the appliance control "OFF" does not remove electrical power from the unit's wiring. • Replace all parts and panels before operating. ! WARNING Electrocution H...
Page 22 - Plumbing Problems
2 2 TROUBLESHOOTING THE ICE MACHINE Plumbing Problems Is the drain hose aligned over the drain ? Move the ice machine to align the drain. Is the ice machine draining properly ? Check that there are no kinks or restrictions in the drain lines; this can cause water to back up in the ice bin. Check tha...
Page 23 - PREPARING THE ICE MACHINE FOR STORAGE
23 Clean the Ice Machine Cleaning the ice machine will help prevent mold and mildew growth as well as sanitize the ice machine for storage or when it is put back into service. See page 17 for instructions for cleaning the ice machine. Draining and Removing Water from the Ice- Making System with a Gr...
Page 24 - To disconnect the water outlet; Draining Water for Factory Installed Drain
24 PREPARING THE ICE MACHINE FOR STORAGE 8. Reconnect the water valve outlet water line. (See Figure 31 and 31 a). 9. Reinstall the ice machine’s access cover. 10. Clean and dry the ice machine’s storage bin. 11. Prop the door open for air circulation to prevent mold and mildew. 12. Leave the water ...
Page 26 - DRAIN PUMP REMOVAL INSTRUCTIONS
26 DRAIN PUMP REMOVAL INSTRUCTIONS Rear of ice machine Front of ice machine Remove the hex nut on front drain pump bracket with the 3 ⁄ 8 " socket then remove the bracket. Remove the hex nut on rear drain pump bracket with the 3 ⁄ 8 " socket then remove the bracket. carriage bolt carriage bo...
Page 27 - Additional issues to be inspected by
27 DRAIN PUMP REMOVAL INSTRUCTIONS Additional issues to be inspected by the installer upon service replacement: 1. The drain pump must be level. 2. No pinched water lines. 3. No interference with electrical cords or wiring. 4. The drain pump should not set on any obstacles, wiring, etc. 5. Secure al...
