Dakota Digital 650360 - Manual
Dakota Digital 650360 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 3 – NOTE: If all screens with displayable data are set to “; OFF; ”, a message will appear during normal operation stating
- Page 4 – SCREEN SPECIAL FUNCTIONS:
- Page 5 – Troubleshooting guide.; Problem
1
MAN #650360
Operating Manual for
Clock / Auxiliary Displays for VHX systems
The VHX auxiliary display module is designed to work with a Dakota Digital VHX system and will not function properly
on its own. W ith this module, an additional display area is added to your current system to provide more functionality.
This module can be used as a simple clock display or it can display data from any BIM module attached to the system
as well as several gauge values from the control box sensors.
Most versions of this module come with at least one switch in the face to allow the display to change between various
screens. Some versions may also contain two additional switches in the face which can be used as the SW1 and SW2
for the VHX control box with the use of the switch harness provided with it.
CONNECTION:
The auxiliary display has a connector on the rear that will accept a normal CAT 5, CAT 5E, or CAT 6 patch cable.
This can be used to connect the module to any available port on the VHX control box (same locations the main
VHX gauges plug into).
A
C
C
.
P
O
W
E
R
C
O
N
S
T
.
P
O
W
E
R
G
R
O
U
N
D
T
A
C
H
W
A
R
N
S
P
D
+
S
P
D
S
N
D
S
P
D
-
S
P
D
O
U
T
S
W
2
(
-)
S
W
1
(
-)
A
D
J
S
N
D
A
D
J
-
W
T
R
S
N
D
W
T
R
-
O
IL
+
O
IL
S
N
D
O
IL
-
F
U
E
L
+
F
U
E
L
S
N
D
F
U
E
L
-
W
A
IT
(
+
)
C
R
U
IS
E
(
-)
G
E
A
R
(
1
W
IR
E
)
4
x
4
(
-)
R
IG
H
T
(
+
)
L
E
F
T
(
+
)
H
IG
H
(
+
)
B
R
A
K
E
(
-)
C
H
E
C
K
E
N
G
(
-)
VHX
CONTROL BOX
CABLE
AUX.
I/O
DISPLAY
www.dakotadigital.com
605-332-6513
D
IM
(
+
)
ORANGE
GREEN
Used for displays
with 3 switches
Connection for all
auxiliary displays
Use any open jack
Auxiliary Display module
VHX
control
box
OR
SWITCH HARNESS:
Some auxiliary modules will come with the
pictured switch harness to allow additional
switches in the clock face to function as switch
1 and 2 for the main VHX system.
Auxiliary modules with 3 switches on front:
Connect the orange wire to SW 1(-) terminal on VHX control box. Right switch will be SW 1 (speed display).
Connect the green wire to SW 2(-) terminal on VHX control box. Left switch will be SW 2 (tach display).
Leave blue wire unconnected. Center switch will be SW3 (clock display)
Auxiliary modules with no switches on front:
If the module has no switches, connect an external switch from the blue wire of the harness to ground to allow
switch operations for the clock display. The orange and green wires would be left unconnected in this case.
ORANGE (switch 1)
GREEN (switch 2)
BLUE (switch 3)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
3 MAN #650360 TEMP UNIT: This setting determines which temperature unit is used when displaying temperatures. This unit setting will be independent of the units used in the main VHX system and may be used to provide and alternate display unit from the main VHX screens if so desired. Default setting ...
4 MAN #650360 AVAILABLE SCREENS: Some screen data should always be available to this module from most VHX systems. These screens are: Clock Engine Temp Oil Pressure Fuel Level Tachometer Speed (MPH) Speed (km/hr) Additionally, depending on the configuration of your main VHX system, many other screen...
5 MAN #650360 USING CLOCK OFFSET: Because this auxiliary module displays the clock, it may be desired to disable the display of the clock on the main VHX screens. This makes it much more difficult to adjust the VHX clock because the main VHX system requires the clock screen to be displayed to set it...
