Cisco OL-7765-04 - Manual
Cisco OL-7765-04 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m; Connecting the Console Port
- Page 3 – Console port
- Page 4 – Connecting the Console Port to a PC; To connect the console port to a PC, follow these steps:; Connecting the 10/100 Ethernet Management Port
- Page 5 – Using the Switch Setup Utility; “Connecting the Console Port to a PC”; After powering on the switch, you see the following output:
- Page 6 – Enter yes to enter setup mode.
- Page 7 – Enter no (no is the default) to not create any additional accounts.; Enter a name for the switch.; Enter the IP address for the mgmt0 interface.; Enter no (no is the default) to not configure the NTP server.
- Page 8 – Enter on (on is the default) to configure the switch port trunk mode.; This step denies traffic flow for all members of the default zone.; Enter yes (yes is the default) to use and save this configuration.
- Page 9 – Verifying the Module Status; A sample output of the show module command follows:
C H A P T E R
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m
2-1
Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide
OL-7765-04
2
Initial Switch Configuration
This chapter provides instructions for setting up the hardware, connecting to the console port, and
initially configuring the switch from the CLI.
This chapter includes the following sections:
•
Preparing for Network Connections, page 2-1
•
Connecting the Console Port, page 2-2
•
Connecting the 10/100 Ethernet Management Port, page 2-4
•
Using the Switch Setup Utility, page 2-5
•
Verifying the Module Status, page 2-9
Preparing for Network Connections
When preparing your site for network connections to the Cisco MDS 9000 switch, consider the
following:
•
Cabling required for each interface type
•
Distance limitations for each signal type
•
Additional interface equipment needed
Before installing a device, have all additional external equipment and cables available.
Configuration Prerequisites
Before you configure a switch in the Cisco MDS 9000 Family for the first time, make sure you have the
following information:
•
Administrator password.
•
Switch name—This name is also used as your switch prompt.
•
IP address for the switch’s management interface.
•
Subnet mask for the switch's management interface.
•
IP address of the default gateway.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-2 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Connecting the Console Port Connecting the Console Port This section describes ...
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-3 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Connecting the Console Port Figure 2-3 Connecting the Console Cable to a Cisco ...
S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-4 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Connecting the 10/100 Ethernet Management Port Connecting the Console Port to a...
