Cisco OL-7765-04 - Manuals - manualsarea.com

Page 2 - S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m; Connecting the Console Port

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-2 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Connecting the Console Port Connecting the Console Port This section describes ...

Page 3 - Console port

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-3 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Connecting the Console Port Figure 2-3 Connecting the Console Cable to a Cisco ...

Page 4 - Connecting the Console Port to a PC; To connect the console port to a PC, follow these steps:; Connecting the 10/100 Ethernet Management Port

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-4 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Connecting the 10/100 Ethernet Management Port Connecting the Console Port to a...

Page 5 - Using the Switch Setup Utility; “Connecting the Console Port to a PC”; After powering on the switch, you see the following output:

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-5 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Connecting to the MGMT 10/100/1000 Ethernet Port If only the active supervisor ...

Page 6 - Enter yes to enter setup mode.

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-6 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Using the Switch Setup Utility General Software Pentium III Embedded BIOS 2000 ...

Page 7 - Enter no (no is the default) to not create any additional accounts.; Enter a name for the switch.; Enter the IP address for the mgmt0 interface.; Enter no (no is the default) to not configure the NTP server.

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-7 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Using the Switch Setup Utility Would you like to enter the basic configuration ...

Page 8 - Enter on (on is the default) to configure the switch port trunk mode.; This step denies traffic flow for all members of the default zone.; Enter yes (yes is the default) to use and save this configuration.

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-8 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Using the Switch Setup Utility Step 18 Enter on (on is the default) to configur...

Page 9 - Verifying the Module Status; A sample output of the show module command follows:

S e n d d o c u m e n t a t i o n c o m m e n t s t o m d s f e e d b a c k - d o c @ c i s c o . c o m 2-9 Cisco MDS 9000 Family Fabric Manager Quick Configuration Guide OL-7765-04 Chapter 2 Initial Switch Configuration Verifying the Module Status Verifying the Module Status Before you proceed with...