Cisco MC-413 - Manual
Cisco MC-413 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Protocol
- Page 3 – Q.SIG Prerequisite Tasks; Q.SIG Configuration Task List; Configuring VoIP Q.SIG; Command; Note
- Page 4 – isdn
- Page 5 – interface serial 0:23
- Page 6 – Verifying VoIP Q.SIG Software on the Cisco AS5300; Enters controller configuration mode.; Exits controller configuration mode.
- Page 7 – Q.SIG for VoIP Configuration Example
- Page 9 – Configuring Q.SIG PRI Signalling Support on the Cisco MC3810
- Page 12 – interface bri 0; codec
- Page 13 – Q.SIG PRI Signalling on the Cisco MC3810 Configuration Example
- Page 15 – Configuring Transparent CCS on the Cisco MC3810; Configuring CCS Cross-Connect
- Page 16 – Configuring CCS Cross-Connect for T1; mode ccs cross-connect
- Page 17 – Configuring T1/E1 Trunk Bearer Channels; type; mode ccs
- Page 18 – Configuring CCS Frame-Forwarding
- Page 19 – A channel configured as; options are available only when the
- Page 21 – CCS Frame-Forwarding Configuration Example
MC-413
Cisco IOS Multiservice Applications Configuration Guide
Configuring Support for PBX Signalling Protocols
This chapter describes how to configure support for PBX signalling formats such as Q.SIG and
transparent common channel signalling (CCS). Configuring support for these signalling protocols on
your router enables the router to interoperate with PBXs running these signalling protocols.
This chapter includes the following sections:
•
Configuring Q.SIG PRI Signalling Support
•
Configuring Transparent CCS on the Cisco MC3810
For a complete description of the commands used in this chapter, refer to the
Cisco IOS Multiservice
Applications Command Reference
. To locate documentation of other commands that appear in this
chapter, use the command reference master index or search online.
Configuring Q.SIG PRI Signalling Support
Configuration Tasks for Q.SIG PRI signalling support are described in the following sections:
•
Configuring Voice over IP Q.SIG Network Transparency on the Cisco AS5300
•
Configuring Q.SIG PRI Signalling Support on the Cisco MC3810
Although the procedures for configuring Q.SIG signalling support on the Cisco AS5300 and on the
Cisco MC3810 are very similar, implementation differences are described in the respective sections.
Benefits of Q.SIG
On both the Cisco AS5300 and the Cisco MC3810, Q.SIG voice signalling provides the following
benefits:
•
Enables Cisco devices to connect with digital PBXs that use the Q.SIG form of CCS.
•
Provides access to multiple remote PBXs with a single connection to a Cisco device.
•
Provides transparent support for supplementary PBX services, so that proprietary PBX features are
not lost when connecting PBXs to Cisco AS5300 and Cisco MC3810 networks.
•
Provides Q.SIG support based on widely used ISDN Q.931 standards. Cisco Q.SIG implementation
follows the following European Telecommunications Standards Institute (ETSI) implementation
standards:
–
ECMA 143:
Private Telecommunication Network (PTN) Inter-exchange Signalling Protocol
Circuit Mode Basic Services
. (This specification covers Q.SIG basic call services.)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-414 Cisco IOS Multiservice Applications Configuration Guide – ECMA 142: Specification, Functional Model and Information Flows for Control Aspects of Circuit Mode Basic Services in Private Telecommunication N...
Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-415 Cisco IOS Multiservice Applications Configuration Guide • Q.SIG data calls are not supported. All calls with bearer capability indicating a nonvoice type (such as video telephony) are rejected. • The inc...
Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-416 Cisco IOS Multiservice Applications Configuration Guide Step 2 Router(config )# controller { T1 | E1 } controller number Enters controller configuration mode. Step 3 Router(config-controller)# pri-group ...
