Cisco MC-413 - Manuals

Cisco MC-413 – Manual in PDF format online.

Manuals:

Manual

Manual Cisco MC-413

Summary

Page 2 - Protocol

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-414 Cisco IOS Multiservice Applications Configuration Guide – ECMA 142: Specification, Functional Model and Information Flows for Control Aspects of Circuit Mode Basic Services in Private Telecommunication N...

Page 3 - Q.SIG Prerequisite Tasks; Q.SIG Configuration Task List; Configuring VoIP Q.SIG; Command; Note

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-415 Cisco IOS Multiservice Applications Configuration Guide • Q.SIG data calls are not supported. All calls with bearer capability indicating a nonvoice type (such as video telephony) are rejected. • The inc...

Page 4 - isdn

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-416 Cisco IOS Multiservice Applications Configuration Guide Step 2 Router(config )# controller { T1 | E1 } controller number Enters controller configuration mode. Step 3 Router(config-controller)# pri-group ...

Page 5 - interface serial 0:23

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-417 Cisco IOS Multiservice Applications Configuration Guide As shown in the preceding section, you have a choice of configuring the isdn-switch-type command to support Q.SIG at either the global configuratio...

Page 6 - Verifying VoIP Q.SIG Software on the Cisco AS5300; Enters controller configuration mode.; Exits controller configuration mode.

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-418 Cisco IOS Multiservice Applications Configuration Guide Figure 97 Q.SIG Signalling Configuration with NEC PBX To configure NEC Fusion signalling support on the Cisco AS5300, use the following commands be...

Page 7 - Q.SIG for VoIP Configuration Example

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-419 Cisco IOS Multiservice Applications Configuration Guide Q.SIG for VoIP Configuration Example The following configuration example configures interface serial 1:23 for Q.SIG PRI and to act as the Q.SIG sla...

Page 9 - Configuring Q.SIG PRI Signalling Support on the Cisco MC3810

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-421 Cisco IOS Multiservice Applications Configuration Guide no ip directed-broadcast isdn switch-type primary-qsig isdn protocol-emulate network isdn incoming-voice modem ! interface FastEthernet0 no ip addr...

Page 12 - interface bri 0; codec

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-424 Cisco IOS Multiservice Applications Configuration Guide As shown in the procedure, you have a choice of configuring the isdn-switch-type command to support Q.SIG at either the global configuration level ...

Page 13 - Q.SIG PRI Signalling on the Cisco MC3810 Configuration Example

Configuring Support for PBX Signalling Protocols Configuring Q.SIG PRI Signalling Support MC-425 Cisco IOS Multiservice Applications Configuration Guide Q.SIG PRI Signalling on the Cisco MC3810 Configuration Example The following configuration example configures interface serial 1:15 for QSIG PRI, a...

Page 15 - Configuring Transparent CCS on the Cisco MC3810; Configuring CCS Cross-Connect

Configuring Support for PBX Signalling Protocols Configuring Transparent CCS on the Cisco MC3810 MC-427 Cisco IOS Multiservice Applications Configuration Guide dial-peer voice 10 vofr destination-pattern 4... session target Serial0 30 ! end Configuring Transparent CCS on the Cisco MC3810 The Cisco M...

Page 16 - Configuring CCS Cross-Connect for T1; mode ccs cross-connect

Configuring Support for PBX Signalling Protocols Configuring Transparent CCS on the Cisco MC3810 MC-428 Cisco IOS Multiservice Applications Configuration Guide Configuring CCS Cross-Connect for T1 When you configure CCS cross-connect for T1, you need to cross-connect from the first T1 controller to ...

Page 17 - Configuring T1/E1 Trunk Bearer Channels; type; mode ccs

Configuring Support for PBX Signalling Protocols Configuring Transparent CCS on the Cisco MC3810 MC-429 Cisco IOS Multiservice Applications Configuration Guide Configuring T1/E1 Trunk Bearer Channels If you will use CCS cross-connect for bearer channels of the T1/E1 trunk, you will need to perform s...

Page 18 - Configuring CCS Frame-Forwarding

Configuring Support for PBX Signalling Protocols Configuring Transparent CCS on the Cisco MC3810 MC-430 Cisco IOS Multiservice Applications Configuration Guide The voice channel type configured as the ext-sig-master is considered the master side of the permanent virtual circuit (PVC) connection and ...

Page 19 - A channel configured as; options are available only when the

Configuring Support for PBX Signalling Protocols Configuring Transparent CCS on the Cisco MC3810 MC-431 Cisco IOS Multiservice Applications Configuration Guide Note When CCS frame-forwarding is configured, the speed (clock rate) of serial interface 1 on the Cisco MC3810 is limited to a maximum of 19...

Page 21 - CCS Frame-Forwarding Configuration Example

Configuring Support for PBX Signalling Protocols CCS Frame-Forwarding Configuration Example MC-433 Cisco IOS Multiservice Applications Configuration Guide CCS Frame-Forwarding Configuration Example The following configuration example configures CCS frame-forwarding on controller E1. Other commands n...