Cisco IGX 8 - Manual
Cisco IGX 8 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Voice Circuit Support
- Page 3 – Data Channel Support
- Page 4 – Digital Data Service Interface
- Page 5 – T1 Interface
- Page 6 – E1 Interface
- Page 7 – T3 Interface
- Page 8 – E3 Interface
- Page 9 – Frame Relay Interface
- Page 11 – Network Management Control
A P P E N D I X
-1
System Specifications
A
This appendix contains system specifications.
General
This section provides general system information on the IGX 8.
System Capacity:
1 shelf with 8 card slots.
Requires 2 dedicated front slot(s) for NPMs.
Requires 2 dedicated back slots for SCMs (1 slot with blank plate).
Up to 6 T1/E1 circuit ports.
Up to 6 T1/E1 packet trunks.
Up to 48 synchronous data ports.
Up to 25 Voice, Data, and/or Frame Relay Module groups.
Enclosure Size:
IGX 8 Standalone/Rackmount:
Height: 25 ins. (63.5 cm) standalone; 24.5 ins. (62.3 cm), rack
Width: 19.9 ins. (50.5 cm), standalone; 19 ins. (48.3 cm.), rack
Depth: 26.5 ins. (67.3 cm), standalone and rack-mount
Shipping Weight:
270 pounds (122.7 kilograms)
Clearance Requirement:
Min. clearance: 30 inches front; nominal 30 ins. rear; 12 ins. side.
Power Input Voltage:
AC system: 100 to 240 VAC (90–264 under-voltage and
over-voltage tolerance), 47 to 63 Hz.
DC system: –42 to –56 VDC.
Each AC supply can provide up to 400 watts to the card shelves.
Space for 4 power supplies.
Current Requirements:
Configuration dependent - use Network Design Tool for exact
requirements. For planning purposes, use the following:
• AC System
10 Amps Max. for 110 VAC, 5 A for 220 VAC.
• DC System
20 Amps max. at –48 VDC; 25 Amps at –42 VDC (worst case)
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
-2 IGX 8 Installation Manual, Release 8.2.0 Voice Circuit Support Input AC PowerConnector: IEC 16 Amp input connector. 6 different power cords are availableto comply with the standards of individual countries. Power cordsare 6 feet (about 2 meters) long. See AC Power Cabling for details. DC Input Co...
-3 Data Channel Support Sync. Data Interfaces: RS-232C/D, RS-449/422, V.24, X.21, and V.35with IGX 8 as DCE or DTE. High-Speed Data Rates(HDM): 2.4 Kbps to 1.344 Mbps. Low-Speed Data Rates: 2.4 to 19.2 Kbps per LDM port. Ports per card: LDI: 4 or 8.SDI: 4. Control Leads Supported: SDI: Per interface...
-4 IGX 8 Installation Manual, Release 8.2.0 Digital Data Service Interface Ports per card: Four. Electrical Interface: Digital Data System (DDS)—AT&T Pub. 62310, November 1987. Interface Type: DSU or OCU (software selectable). Data Rates: 2.4, 4.8, 9.6, 19.2, and 56 Kbps (software selectable). D...
