Cisco 535 - Manual
Cisco 535 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – shows the front view of the PIX 535.
- Page 4 – PIX 535 Network Interface Description; The slots and buses are configured as follows:
- Page 5 – Installing the PIX 535; PIX 535 Network Interface Installation, page 7-6; Before Installing the PIX 535; Regulatory Compliance and Safety Information; Gigabit Ethernet Card
- Page 6 – PIX 535 Network Interface Installation; Note; PIX 535 Feature Licenses; “Installing Failover” section on page 7-8; logging; command page
- Page 7 – configuration guide; VPN Accelerator Card; VPN Accelerator Card+; Load sharing ESP and AH activity between up to three VAC+.
- Page 8 – Installing Failover; To set up a failover connection, perform the following steps:
- Page 9 – Caution; Installing LAN-Based Failover
- Page 10 – Replacing a Lithium Battery
- Page 11 – Installing a Memory Upgrade; The following statement applies to DC models only:
- Page 12 – Locate the system memory sockets (see
- Page 13 – and; Rack-mount the chassis or place it on a flat, stable surface.
- Page 14 – show version; Installing a Circuit Board in the PIX 535; PIX 535 Circuit Board Options
- Page 15 – Restricted Interface Options; GE + 1 VPN Accelerator
- Page 16 – Circuit Board Slot Description; There are nine circuit board slots (see
- Page 17 – Installing a Circuit Board; Use the screw that was removed in
- Page 18 – 6 MB Flash Circuit Board
- Page 19 – clear flashfs
- Page 20 – VPN Accelerator Circuit Board; Gigabit Ethernet Circuit Board; 000SXfull—Forces full-duplex operation
- Page 21 – Installing the PIX 535 DC Model; Warning
- Page 22 – As shown in; Refer to
- Page 23 – If needed, install the interface boards as described in the
C H A P T E R
7-1
Cisco PIX Security Appliance Hardware Installation Guide
78-15170-03
7
PIX 535
This chapter describes the installation of the PIX 535, and includes the following sections:
•
PIX 535 Product Overview, page 7-1
•
Installing the PIX 535, page 7-5
•
PIX 535 Feature Licenses, page 7-6
•
•
Installing LAN-Based Failover, page 7-9
•
Replacing a Lithium Battery, page 7-10
•
Installing a Memory Upgrade, page 7-11
•
Installing a Circuit Board in the PIX 535, page 7-14
•
Installing the PIX 535 DC Model, page 7-21
PIX 535 Product Overview
Note
The PIX 535 chassis cover should not be removed. The user-serviceable components are accessed by a
removable tray at the back panel of each model. If you need to remove the PIX 535 chassis cover for any
reason, use the related information in the
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
7-2 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 PIX 535 Product Overview Figure 7-1 shows the front view of the PIX 535. Figure 7-1 PIX 535 Front Panel Figure 7-2 shows the rear view of the PIX 535. Figure 7-2 PIX 535 Rear Panel The PIX 535 has a fixed RJ-4...
7-4 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 PIX 535 Product Overview PIX 535 Network Interface Description There are three separate buses for the nine interface slots in the PIX 535. The interfaces are counted from right to left on the PIX 535. The slot...
7-5 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing the PIX 535 Table 7-3 lists the relative throughput of the Gigabit Ethernet combinations. Installing the PIX 535 This section includes the following topics: • Before Installing the PIX 535, page 7-5...
