Cisco 535 - Manuals

Cisco 535 – Manual in PDF format online.

Manuals:

Manual

Manual Cisco 535

Summary

Page 2 - shows the front view of the PIX 535.

7-2 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 PIX 535 Product Overview Figure 7-1 shows the front view of the PIX 535. Figure 7-1 PIX 535 Front Panel Figure 7-2 shows the rear view of the PIX 535. Figure 7-2 PIX 535 Rear Panel The PIX 535 has a fixed RJ-4...

Page 4 - PIX 535 Network Interface Description; The slots and buses are configured as follows:

7-4 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 PIX 535 Product Overview PIX 535 Network Interface Description There are three separate buses for the nine interface slots in the PIX 535. The interfaces are counted from right to left on the PIX 535. The slot...

Page 5 - Installing the PIX 535; PIX 535 Network Interface Installation, page 7-6; Before Installing the PIX 535; Regulatory Compliance and Safety Information; Gigabit Ethernet Card

7-5 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing the PIX 535 Table 7-3 lists the relative throughput of the Gigabit Ethernet combinations. Installing the PIX 535 This section includes the following topics: • Before Installing the PIX 535, page 7-5...

Page 6 - PIX 535 Network Interface Installation; Note; PIX 535 Feature Licenses; “Installing Failover” section on page 7-8; logging; command page

7-6 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 PIX 535 Feature Licenses PIX 535 Network Interface Installation Note If your PIX security appliance model supports a failover configuration, complete the steps that follow only on the active (primary) unit. To...

Page 7 - configuration guide; VPN Accelerator Card; VPN Accelerator Card+; Load sharing ESP and AH activity between up to three VAC+.

7-7 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 PIX 535 Feature Licenses For information on upgrading feature licenses or downloading the latest software versions, refer to the configuration guide online at : http://www.cisco.com/en/US/products/sw/secursw/p...

Page 8 - Installing Failover; To set up a failover connection, perform the following steps:

7-8 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing Failover Installing Failover To set up a failover connection, perform the following steps: Step 1 Power off both the primary and secondary units. Note Both chassis must be the same model number, hav...

Page 9 - Caution; Installing LAN-Based Failover

7-9 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing LAN-Based Failover Caution Do not turn the power on until the units are connected and the primary unit is configured completely. Step 7 Power the primary unit on first, then power on the secondary u...

Page 10 - Replacing a Lithium Battery

7-10 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Replacing a Lithium Battery Figure 7-6 LAN-Based Failover Connections Step 5 If you are using Stateful Failover, use one of the following types of connections, that is appropriate for your system, between the...

Page 11 - Installing a Memory Upgrade; The following statement applies to DC models only:

7-11 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Memory Upgrade Installing a Memory Upgrade The following statement applies to DC models only: Warning Before performing any of the following procedures, ensure that power is removed from the DC c...

Page 12 - Locate the system memory sockets (see

7-12 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Memory Upgrade Step 7 Locate the system memory sockets (see Figure 7-7 ). Populate memory Bank 0 first, then Bank 1. Memory sockets J40 and J43 comprise Bank 0; J41 and J44 comprise Bank 1. The P...

Page 13 - and; Rack-mount the chassis or place it on a flat, stable surface.

7-13 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Memory Upgrade Step 8 Install the first DIMM strip in socket J41 and the second DIMM strip in socket J44, as shown in Figure 7-8 and Figure 7-9 . a. Carefully grasp the DIMM strip from either end...

Page 14 - show version; Installing a Circuit Board in the PIX 535; PIX 535 Circuit Board Options

7-14 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Circuit Board in the PIX 535 Step 12 Reconnect all cables to the security appliance and plug it into its power source. Step 13 Power on the security appliance. Note You can verify that the securi...

Page 15 - Restricted Interface Options; GE + 1 VPN Accelerator

7-15 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Circuit Board in the PIX 535 Table 7-4 PIX 535 Interface Options Restricted Interface Options Unrestricted Interface Options 8 GE 9 GE 8 GE + 1 VPN Accelerator 8 GE + 1 FE 7 GE + 1 FE 8 GE + 1 VP...

Page 16 - Circuit Board Slot Description; There are nine circuit board slots (see

7-16 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Circuit Board in the PIX 535 Circuit Board Slot Description There are nine circuit board slots (see Figure 7-10 ) using three separate buses for the PIX 535. Figure 7-10 PIX 535 Back Panel Detail...

Page 17 - Installing a Circuit Board; Use the screw that was removed in

7-17 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Circuit Board in the PIX 535 Installing a Circuit Board Note It is not necessary to remove the chassis cover on the PIX 535 to install or replace a circuit board. A component tray, that slides ou...

Page 18 - 6 MB Flash Circuit Board

7-18 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Circuit Board in the PIX 535 Figure 7-12 4-Port Circuit Board Overlap Note If you are installing a 4-port circuit board, note that the circuit board will overlap the slot connector on the motherb...

Page 19 - clear flashfs

7-19 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Circuit Board in the PIX 535 An illustration of the 16 MB Flash circuit board is shown in Figure 7-13 . Figure 7-13 16 MB Flash Circuit Board You must observe the following when installing a 16 M...

Page 20 - VPN Accelerator Circuit Board; Gigabit Ethernet Circuit Board; 000SXfull—Forces full-duplex operation

7-20 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing a Circuit Board in the PIX 535 Step 5 Remove any previously installed Flash memory circuit boards from the unit. Step 6 The jumper on the PIX security appliance 16 MB Flash circuit board must not b...

Page 21 - Installing the PIX 535 DC Model; Warning

7-21 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing the PIX 535 DC Model Note You must use a GE failover link when connecting the PIX 535 with GE interfaces. The Gigabit Ethernet circuit board and the fiber optic cable connection are shown in Figure...

Page 22 - As shown in; Refer to

7-22 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing the PIX 535 DC Model Step 3 Terminate the DC input wiring on a DC source capable of supplying at least 15 amps. A 15-amp circuit breaker is required at the -48 VDC facility power source. An easily ...

Page 23 - If needed, install the interface boards as described in the

7-23 Cisco PIX Security Appliance Hardware Installation Guide 78-15170-03 Chapter 7 PIX 535 Installing the PIX 535 DC Model Step 9 Reconnect power to the PIX 535. After wiring the DC power supply, remove the tape from the circuit breaker switch handle and reinstate power by moving the handle of the ...