Cisco 2948G-L3 - Manual
Cisco 2948G-L3 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Using the Console and the Management Ports; Modem Support; Modem Support for Recovering a System Image
- Page 3 – Passwords; Configuring the Management Port
- Page 5 – Configuring the Hostname; Viewing the Contents of Bootflash Memory
- Page 6 – Deleting Files from Bootflash Memory; Backing Up a System Image to a TFTP Server
- Page 8 – Erasing Files from a Full Bootflash Memory SIMM
- Page 10 – Recovering a System Image Using Xmodem and Ymodem
- Page 11 – Example of Xmodem Transfer Using the ROM Monitor Mode
- Page 13 – Updating the System Image; Downloading System Images from Cisco.com; Copying the System Image to the Layer 3 Switch Router
- Page 15 – Reloading the Layer 3 Switch Router
C H A P T E R
3-1
Catalyst 2948G-L3 and Catalyst 4908G-L3 Switch Router Software Feature and Configuration Guide
78-10408-03
3
Configurations for the Layer 3 Switch Router
This chapter describes the initial configuration of the Layer 3 switch router and contains the following
major sections:
•
Starting Up the Layer 3 Switch Router, page 3-1
•
Using the Console and the Management Ports, page 3-2
•
Configuring the Management Port, page 3-3
•
Configuring the Hostname, page 3-5
•
Using the Bootflash Memory SIMM, page 3-5
•
Recovering a System Image Using Xmodem and Ymodem, page 3-10
•
Updating the System Image, page 3-13
This chapter takes you through Step 2 of the suggested process for configuring your Layer 3 switch
router (see the
“Preparing to Configure the Layer 3 Switch Routers” section on page 2-1
Note
You should have already set up the hardware before proceeding with the initial Layer 3 switch router
configuration.
Starting Up the Layer 3 Switch Router
Note
You must complete the tasks described here before configuring your Layer 3 switch router.
This section lists the tasks you should have completed during hardware installation, including starting
up the Layer 3 switch router. You should have:
•
Verified that the Layer 3 switch router is set for the correct AC (or DC) power voltages.
Refer to the
Catalyst 2948G-L3 Hardware Installation Guide
or the
Catalyst 4908G-L3 Hardware
Installation Guide
for correct power voltages.
•
Connected the cables to the Layer 3 switch router.
•
Connected the console terminal to the Layer 3 switch router.
•
Powered up the Layer 3 switch router.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
3-2 Catalyst 2948G-L3 and Catalyst 4908G-L3 Switch Router Software Feature and Configuration Guide 78-10408-03 Chapter 3 Configurations for the Layer 3 Switch Router Using the Console and the Management Ports • Entered the command line interface (CLI) configuration mode. You do this by answering no ...
3-3 Catalyst 2948G-L3 and Catalyst 4908G-L3 Switch Router Software Feature and Configuration Guide 78-10408-03 Chapter 3 Configurations for the Layer 3 Switch Router Configuring the Management Port file transfer. The maximum file transfer speed supported is 57600 baud. This functionality primarily s...
3-5 Catalyst 2948G-L3 and Catalyst 4908G-L3 Switch Router Software Feature and Configuration Guide 78-10408-03 Chapter 3 Configurations for the Layer 3 Switch Router Configuring the Hostname • To see the configuration in NVRAM, enter the following command: Router# show startup-config If you made cha...
