Cisco 1805 - Manual
Cisco 1805 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Warning; Modules Internal to the Cisco 1805 Cable Router; “Opening the Chassis” section on page 8-2; Opening the Chassis
- Page 3 – Removing the Chassis Screw; Router cover fastening screw; Screwdriver pry points
- Page 4 – Removing the Cover of the Cisco 1805 Router; Locating Modules; Slide cover back from router chassis
- Page 5 – Caution; Installing a SODIMM
- Page 6 – Removing a SODIMM; Insert the SODIMM into the SODIMM socket, as shown in; Installing an AIM; SODIMM
- Page 7 – Accessory Kit to Use; Location of Metal Standoff Attachment Locations; System board
- Page 8 – Insert the plastic standoff (; Plastic Standoff Orientation
- Page 9 – Connecting the AIM to the System Board; Note; Metal standoffs
- Page 10 – Correctly Installed AIM; Applying the AIM Label; Peel the chassis label from its backing.; Closing the Chassis; To close the chassis, follow these steps:
- Page 11 – Rotate cover onto router
C H A P T E R
8-1
Cisco 1805 DOCSIS Cable Router Hardware Installation Guide
OL-14661-01
8
Installing and Upgrading Internal Modules in
Cisco 1805 Cable Routers
This chapter describes how to install or upgrade modules that are located internally within the
Cisco 1805 DOCSIS cable router: memory modules and advanced integration modules (AIMs). You
need to remove the cover from the router to install or remove any of these items. The chapter contains
the following sections:
•
•
Modules Internal to the Cisco 1805 Cable Router, page 8-2
Note
Before you install, operate, or service the system, read the
Regulatory Compliance and Safety
Information for Cisco 1840 Routers
for important safety information and translations of the warnings
that appear in this guide.
Safety Warnings
Warning
Before working on a system that has an on/off switch, turn OFF the power and unplug the power cord.
Statement 1
Warning
Before working on equipment that is connected to power lines, remove jewelry (including rings,
necklaces, and watches). Metal objects will heat up when connected to power and ground and can
cause serious burns or weld the metal object to the terminals.
Statement 43
Warning
During this procedure, wear grounding wrist straps to avoid ESD damage to the card. Do not directly
touch the backplane with your hand or any metal tool, or you could shock yourself.
Statement 94
Warning
Do not work on the system or connect or disconnect cables during periods of lightning activity.
Statement 1001
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
8-2 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Warning Read the installation instructions before you connect the system to its power source. Sta...
8-3 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Figure 8-1 Removing the Chassis Screw Step 4 Insert a flat-head screwdriver into the slots at the...
8-4 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Figure 8-3 Removing the Cover of the Cisco 1805 Router Step 7 Place the router bottom on an antis...
