Cisco 1805 - Manuals - manualsarea.com

Page 2 - Warning; Modules Internal to the Cisco 1805 Cable Router; “Opening the Chassis” section on page 8-2; Opening the Chassis

8-2 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Warning Read the installation instructions before you connect the system to its power source. Sta...

Page 3 - Removing the Chassis Screw; Router cover fastening screw; Screwdriver pry points

8-3 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Figure 8-1 Removing the Chassis Screw Step 4 Insert a flat-head screwdriver into the slots at the...

Page 4 - Removing the Cover of the Cisco 1805 Router; Locating Modules; Slide cover back from router chassis

8-4 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Figure 8-3 Removing the Cover of the Cisco 1805 Router Step 7 Place the router bottom on an antis...

Page 5 - Caution; Installing a SODIMM

8-5 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Figure 8-4 Cisco 1805 Cable Router (Internal View) Caution Do not , under any circumstances, tamp...

Page 6 - Removing a SODIMM; Insert the SODIMM into the SODIMM socket, as shown in; Installing an AIM; SODIMM

8-6 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Figure 8-5 Removing a SODIMM Step 3 Insert the SODIMM into the SODIMM socket, as shown in Figure ...

Page 7 - Accessory Kit to Use; Location of Metal Standoff Attachment Locations; System board

8-7 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Caution When you install an AIM, always wear an ESD-preventive wrist strap, and ensure that it ma...

Page 8 - Insert the plastic standoff (; Plastic Standoff Orientation

8-8 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Step 3 Insert the plastic standoff ( Figure 8-8 ) from the accessory kit into the hole in the sys...

Page 9 - Connecting the AIM to the System Board; Note; Metal standoffs

8-9 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Figure 8-9 Connecting the AIM to the System Board Step 4 Insert the connector on the AIM into the...

Page 10 - Correctly Installed AIM; Applying the AIM Label; Peel the chassis label from its backing.; Closing the Chassis; To close the chassis, follow these steps:

8-10 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Figure 8-10 Correctly Installed AIM Applying the AIM Label The AIM label for the chassis might b...

Page 11 - Rotate cover onto router

8-11 Cisco 1805 DOCSIS Cable Router Hardware Installation Guide OL-14661-01 Chapter 8 Installing and Upgrading Internal Modules in Cisco 1805 Cable Routers Modules Internal to the Cisco 1805 Cable Router Step 4 Use a Phillips’ screwdriver to reinstall the screw that holds the cover to the chassis. S...