Cisco 1010 Series - Manual
Cisco 1010 Series – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Site Preparation; Ensuring Overcurrent Protection
- Page 3 – Rack-Mounting the System; Ensuring Proper Airflow; Stabilizing the System
- Page 5 – Lifting the System
- Page 6 – Power Considerations; AC Power
- Page 7 – Using Redundant Power; Installing and Servicing the System
- Page 8 – Disconnecting Power; Working with Lasers; Preventing EMI; Covering Empty Slots
- Page 9 – Disposing of the System; Regulatory Standards Compliance
- Page 10 – FCC Part 68 Notice
- Page 12 – JATE
- Page 13 – EMC Environmental Conditions in the European Union; FCC Class A warning
- Page 14 – Canada Class A Warning; CISPR 22 Class A Warning
- Page 15 – Class A Notice for Hungary; Korean Class A Warning
- Page 16 – Translated Safety Warnings; Warning Definition
- Page 19 – Backplane Voltage
- Page 20 – Ground Conductor
- Page 21 – Restricted Area Warning
- Page 22 – Qualified Personnel Warning
- Page 25 – Disconnect Device Warning
- Page 26 – Related Documentation
- Page 27 – Platform Documents; Obtaining Documentation
- Page 28 – Ordering Documentation; Documentation Feedback; Obtaining Technical Assistance
- Page 29 – Cisco TAC Website
- Page 30 – Obtaining Additional Publications and Information
Corporate Headquarters:
Copyright © 2003 Cisco Systems, Inc. All rights reserved.
Cisco Systems, Inc., 170 West Tasman Drive, San Jose, CA 95134-1706 USA
Regulatory Compliance and Safety Information
for the Catalyst 8500 and LightStream 1010 Series
Read this document before installing or servicing the following Catalyst 8500 and LightStream 1010
series switches:
•
Catalyst 8540 MSR
•
Catalyst 8510 MSR
•
Catalyst 8540 CSR
•
Catalyst 8510 CSR
•
LightStream 1010 ATM switch
Note
Only trained and qualified service personnel (as defined in IEC 60950 and AS/NZS 3260) should install,
replace, or service the equipment. Install the system in accordance with the U.S. National Electric Code
if you are in the United States.
Warning
This warning symbol means danger. You are in a situation that could cause bodily injury. Before you
work on any equipment, be aware of the hazards involved with electrical circuitry and be familiar
with standard practices for preventing accidents.
Note
The following guidelines are applicable for products intended for use in Australia:
•
Only trained and qualified service personnel should install, replace, or service the equipment, as
defined by AS/NZS 3260.
•
Incorrect connection of this or connected equipment to a general purpose outlet could result in a
hazardous situation.
This document includes the following sections:
•
•
Regulatory Standards Compliance, page 9
•
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 Regulatory Compliance and Safety Information for the Catalyst 8500 and LightStream 1010 Series 78-14229-02 Site Preparation • Related Documentation, page 26 • Obtaining Documentation, page 27 • Obtaining Technical Assistance, page 28 • Obtaining Additional Publications and Information, page 30 Sit...
3 Regulatory Compliance and Safety Information for the Catalyst 8500 and LightStream 1010 Series 78-14229-02 Site Preparation Rack-Mounting the System A rack-mount kit and cable guides come with the system. The kit is not suitable for racks withobstructions (such as a power strip) that could impair ...
5 Regulatory Compliance and Safety Information for the Catalyst 8500 and LightStream 1010 Series 78-14229-02 Site Preparation Figure 2 Catalyst 8510 and LightStream 1010 Chassis Standard Equipment Rack Dimensions • Ensure that the weight of the chassis does not make the rack unstable. Secure telco r...
