Chief JWP-V - Manual
Chief JWP-V – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – IMPORTANT WARNINGS and CAUTIONS!; DIMENSIONAL DRAWING
- Page 3 – CONTENTS; Watch for pinch points. Do not put; SPECIFICATIONS
- Page 4 – INTRODUCTION; Typical VESA Mounting Hole
- Page 5 – PARTS
- Page 6 – JWP Parts List; Item
- Page 7 – SECURE WALL BRACKET; It is the responsibility of the; INSTALLATION; Flush Mount Installation; Figure 1. Secure Wall Bracket
- Page 8 – Recess Mount Installation; Make sure surface is clean and; Figure 3. Recess Mount Centris Bracket to Display
- Page 9 – Interface Bracket Installation; You must use proper attaching; The screw and spacer length must; Figure 4. Attaching Interface Bracket to Display
- Page 10 – Figure 5. Display with 200mm x 100mm Hole Pattern
- Page 11 – Figure 7. Display with 300mm x 200mm Hole Pattern
- Page 12 – Figure 9. Display with 200mm x 200mm Hole Pattern
- Page 13 – Attach Display to Mount (Centris Bracket); Figure 11. Attach Display to Mount
- Page 14 – CABLE MANAGEMENT; Make sure your cables do not run; ADJUSTMENTS; Lateral Tension Adjustment; To adjust Lateral Tension:; Pitch Tension Adjustment; To adjust Pitch Tension:; Figure 14. Adjust Lateral Tension
CHIEF MANUFACTURING INC.
8832-000134 Rev B
1-800-582-6480
952-894-6280 FAX 952-894-6918
©2006 Chief Manufacturing
8401 EAGLE CREEK PARKWAY, STE. 700
SAVAGE, MINNESOTA 55378 USA
12/06
I N S T A L L A T I O N I N S T R U C T I O N S
Medium Flat Panel
Pivot/Pitch Wall Mount
Model JWP-V
The JWP Pivot/Pitch wall mount is designed for
mounting a medium sized flat panel display. The mount
can be tilted up and down to 15° of center as well as
pivot left and right.
The JWP is shipped with the VESA
®
100mm/100mm
Centris™ interface which is compatible with most
medium flat panels.
To accommodate other mounting patterns in displays,
the JWP comes with a VESA Plate that accommodates
other VESA mounting patterns.
By design, the JWP can be configured to fit your medium
flat panel display, providing that your display does not
exceed the specified weight rating.
JWP-V
BEFORE YOU BEGIN
CAUTION:
To prevent damage to your display and/or the JWP, which could affect or void factory
warranty, thoroughly study all instructions and illustrations before you begin to install the mount. Pay
particular attention to ALL Warnings and Cautions in this document.
The maximum weight allowable for use with the JWP wall mount is 75 lbs (34 kg).
The JWP wall mount is designed to be installed using wall studs or supporting framework. The structure to which
the JWP wall mount is anchored must be capable of supporting
five times
the total weight of the mount and all
attached equipment.
If you hav e any questions about this installation, contact Chief Manufacturing at 1-800-582-6480.
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
Installation Instructions JW P-V 2 IMPORTANT WARNINGS and CAUTIONS! WARNING A WARNING alerts you to the possibility of serious injury or death if you do not followthe instructions. CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if youdo not follow the correspon...
Installation Instructions JW P-V 3 CONTENTS DIMENSIONAL DRAW ING ..................................... 2 TOOLS REQUIRED FOR INSTALLATION ............ 3 INSPECT UNIT BEFORE INSTALLING ................. 3 SPECIFICATIONS ................................................... 3 INTRODUCTION ..................
Installation Instructions JW P-V 4 INTRODUCTION There are 3 main steps in the JWP-V installationprocess. These steps are: Selecting an appropriate mounting configuration. Connect display cables Making required adjustments Before starting the installation process, determine thecorrect mounting hole c...
