Chief JWP-V - Manuals - manualsarea.com

Page 2 - IMPORTANT WARNINGS and CAUTIONS!; DIMENSIONAL DRAWING

Installation Instructions JW P-V 2 IMPORTANT WARNINGS and CAUTIONS! WARNING A WARNING alerts you to the possibility of serious injury or death if you do not followthe instructions. CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if youdo not follow the correspon...

Page 3 - CONTENTS; Watch for pinch points. Do not put; SPECIFICATIONS

Installation Instructions JW P-V 3 CONTENTS DIMENSIONAL DRAW ING ..................................... 2 TOOLS REQUIRED FOR INSTALLATION ............ 3 INSPECT UNIT BEFORE INSTALLING ................. 3 SPECIFICATIONS ................................................... 3 INTRODUCTION ..................

Page 4 - INTRODUCTION; Typical VESA Mounting Hole

Installation Instructions JW P-V 4 INTRODUCTION There are 3 main steps in the JWP-V installationprocess. These steps are: Selecting an appropriate mounting configuration. Connect display cables Making required adjustments Before starting the installation process, determine thecorrect mounting hole c...

Page 5 - PARTS

Installation Instructions JW P-V 5 PARTS Figure 2. JWP-V Components Set Screw (see notes) Centris Bracket(See notes) 10 BAG B BAG A BAG C BAG D BAG E

Page 6 - JWP Parts List; Item

Installation Instructions JW P-V 6 PARTS (Continued) Table 2 shows the individual part and parts bags shipped with JWP parts. Table 2. JWP Parts List Item Bag Description Qty Notes 10 — MSP-MA MOUNT (with Centris bracket) 1 20 — Interface Bracket 1 30 — Wall Bracket 1 Use with 40 40 — Lag Screws, 3/...

Page 7 - SECURE WALL BRACKET; It is the responsibility of the; INSTALLATION; Flush Mount Installation; Figure 1. Secure Wall Bracket

Installation Instructions JW P-V 7 SECURE WALL BRACKET WARNING: It is the responsibility of the installer to verify that the surface to which the mountis anchored will safely support the combined load ofall attached components and equipment. Install wall bracket as follows: 1. Determine exact mounti...

Page 8 - Recess Mount Installation; Make sure surface is clean and; Figure 3. Recess Mount Centris Bracket to Display

Installation Instructions JW P-V 8 Recess Mount Installation To recess mount Centris Bracket: 1. Lay display down on a flat surface. CAUTION: Make sure surface is clean and free of dirt and debris before laying display down. 2. Select four screws M4 x 20mm screws (60) and four spacers (100) from par...

Page 9 - Interface Bracket Installation; You must use proper attaching; The screw and spacer length must; Figure 4. Attaching Interface Bracket to Display

Installation Instructions JW P-V 9 Interface Bracket Installation The following sections describe how to install theinterface bracket (20) for a specific hole-pattern onyour display. This procedure provides a general guideline to followwhen installing the interface bracket after selecting themountin...

Page 10 - Figure 5. Display with 200mm x 100mm Hole Pattern

Installation Instructions JW P-V 10 200mm x 100mm Pattern For the 200mm x 100mm hole pattern, do thefollowing: 1. Select six flat head M4 screws (60) from Bag A and six spacers (130) from Bag C. 2. Attach the interface bracket (20) using the hole- pattern on the back of your display as shown inFigur...

Page 11 - Figure 7. Display with 300mm x 200mm Hole Pattern

Installation Instructions JW P-V 11 300mm x 200mm Pattern For the 300mm x 200mm hole pattern, do thefollowing: 1. Select eight Phillips head M6 screws (110) from Bag B and eight spacers (120) from Bag C. 2. Attach the interface bracket (20) using the hole- pattern on the back of your display as show...

Page 12 - Figure 9. Display with 200mm x 200mm Hole Pattern

Installation Instructions JW P-V 12 200mm x 200mm Pattern For the 200mm x 200mm hole pattern, do thefollowing: 1. Select the applicable screws as follows: a. If using square hole on interface bracket (20), select four Phillips head M4 screws from Bag A. OR b. If using round hole on interface bracket...

Page 13 - Attach Display to Mount (Centris Bracket); Figure 11. Attach Display to Mount

Installation Instructions JW P-V 13 Attach Display to Mount (Centris Bracket) After attaching the interface bracket onto thedisplay, the next step is to attach the display to themount (Centris bracket). To attach the display to the Centris bracket, do thefollowing: 1. Select four Phillips head M4 x ...

Page 14 - CABLE MANAGEMENT; Make sure your cables do not run; ADJUSTMENTS; Lateral Tension Adjustment; To adjust Lateral Tension:; Pitch Tension Adjustment; To adjust Pitch Tension:; Figure 14. Adjust Lateral Tension

Installation Instructions JW P-V 14 CABLE MANAGEMENT WARNING: Make sure your cables do not run through a pinch points. Do not put your fingersbetween movable parts. For cable management (not shown), connect andsecure power/audio/video cables, making sure toleave sufficient slack to allow for movemen...