Page 2 - Important; Appliance information:; Declaration of CE conformity
2 Important This appliance is designed and manufactured solely for the cooking of domestic (household) food and is not suitable for any non domestic application and therefore should not be used in a commercial environment. The appliance guarantee will be void if the appliance is used within a non do...
Page 3 - Important Safeguards and Recommendations; technician in order to avoid a hazard.; Before Using for the First Time
3 Important Safeguards and Recommendations – Do not carry out any cleaning or maintenance without first disconnecting the appliance from the electrical supply. – During and after use of the hob, certain parts will become very hot. Do not touch hot parts.– After use always ensure that the control kno...
Page 4 - Features and Technical Data; Cooking Points; This appliance is class 3
4 Features and Technical Data Fig. 1 Cooking Points 1. Auxiliary burner (A) - 1,00 kW 2. Semi-rapid burner (SR) - 1,75 kW3. Rapid burner (R) - 3,00 kW 4. Triple ring burner (TR) - 3,50 kW Control Panel 10. Right auxiliary burner (1) control knob11. Central auxiliary burner (1) control knob12. Triple...
Page 5 - How to use the hob; Gas burners
5 How to use the hob Gas burners Gas flow to the burners is adjusted by turning the knobs (illustrated in fig.2) which control the valves.Turning the knob so that the indicator line points to the symbols printed on the panel achieves the following functions: – Symbol ● : Tap closed (burner off) – Sy...
Page 6 - Choice of Burner; Burner Size
6 WRONG CORRECT Choice of Burner The symbols printed on the panel by the side of the knob indicate which burner you are controlling.Choose a suitable burner depending on the cookware diameter and capacity.The pan diameter should be suitable for the burner power to make the most of the burner's high ...
Page 7 - Cleaning and Maintenance; General Tips; Stainless Steel Surfaces
7 Cleaning and Maintenance General Tips – Before cleaning the hob switch it off and wait for it to cool down.– Clean with a cloth, hot water and soap or liquid detergent.– Do not use products which are abrasive, corrosive or chlorine based.– Do not use steel pads.– Avoid using cleaning products with...
Page 8 - Burners and Grids
8 Fig. 8 Burners and Grids – These parts can be removed and cleaned with appropriate products.– After cleaning, the burners and their flame spreaders must be well dried and correctly replaced. – It is very important to check that the burner flame spreader and the cap have been correctly positioned. ...
Page 9 - Correct Position of Triple Ring Burner
9 Correct Position of Triple Ring Burner The triple ring burner must be correctly positioned (see fig. 9); the burner ribs must be fitted in their housing as shown by the arrow.The burner correctly positioned must not rotate (fig. 10).Then position the cap “A” and the ring “B” (figs. 10 - 11) A B Fi...
Page 11 - Installation; Technical Information for the Installer; Installation in Kitchen Cabinet with Door
11 Installation Technical Information for the Installer In order to install the hob into the kitchen fixture, a hole with the dimensions shown in fig. 12 has to be made, bearing in mind the following:– within the unit, between the bottom of the hob and the upper surface of a shelf there must be a cl...
Page 12 - Fastening the Installation Brackets; Fastening the Hob
12 Fastening the Installation Brackets (fig. 15) – Each hob is provided with an installation kit including brackets and screws for fastening the top to fixture panels from 2 to 4 cm thick. – Turn the hob upside down and fasten the brackets “A” to the appropriate socket holes, without tightening the ...
Page 13 - Gas supply requirements; Important Note
13 Gas supply requirements Important Note This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation label attached on the appliance).– Appliances supplied for use on NATURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modificati...
Page 14 - Gas Connection
14 Gas Connection The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a suitably qualified and registered installer. Installers shall take due account of the provisions of the relevant British Standards Code of Practice, the Gas Safety Regulations and the Building S...
Page 15 - time by brushing the solution over the connection.
15 Gas connection Cat: II 2H3+ The fitting (fig. 17) is made up of:– 1 nut “A”– 1 elbow fitting “C”– gasket “F” Connection to the Gas Supply – Be careful when flexible pipes are used that they do not come into contact with moving parts.– To maintain the thickness of 3 cm, the hob is fitted with a ch...
Page 16 - Conversion to Natural Gas or LPG; Replacing the Burner Injectors; Table for the Choice of the Injectors
16 Conversion to Natural Gas or LPG Replacing the Burner Injectors – Remove the pan supports, the burner caps and flame speaders.– Using a wrench, substitute the nozzle injectors “J” (Figs. 19 - 20) with those most suitable for the kind of gas for which it is to be used. The burners are conceived in...
Page 17 - Regulating the Burner Minimum Setting; For LPG, tighten the adjustment screw completely.; Lubrication of the Gas Taps
17 Regulating the Burner Minimum Setting When changing from one type of gas to another, the minimum tap output must also be correct, considering that in this position the flame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum to the minimum position. ...
Page 18 - Mains Electricity Connection
18 Mains Electricity Connection Incorrect installation may be dangerous and the manufacturer can not be held responsible.Warning! This appliance must be earthed The manufacturer declines all responsibility for any problem caused by failure to observe this rule. THIS APPLIANCE MUST BE CONNECTED TO TH...
Page 19 - Limit of Cover
19 Appliance Servicing CDA provide a quality and effective after-sales service to cover all your servicing needs. Please attach your receipt to this page for safekeeping.Please help us to help you by having the following information available when booking a service-call:1. Model type, make and model...
Page 20 - To contact our Customer Care Department, or for Service,
Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu To contact our Customer Care Department, or for Service, please contact us on the details below. Cod. 1103520/GB - ß4
