CDA HCG 931 - Manuals

5 How to use the hob Gas burners Gas flow to the burners is adjusted by turning the knobs (illustrated in fig.2) which control the valves.Turning the knob so that the indicator line points to the symbols printed on the panel achieves the following functions: – Symbol ● : Tap closed (burner off) – Sy...

6 WRONG CORRECT Choice of Burner The symbols printed on the panel by the side of the knob indicate which burner you are controlling.Choose a suitable burner depending on the cookware diameter and capacity.The pan diameter should be suitable for the burner power to make the most of the burner's high ...

7 Cleaning and Maintenance General Tips – Before cleaning the hob switch it off and wait for it to cool down.– Clean with a cloth, hot water and soap or liquid detergent.– Do not use products which are abrasive, corrosive or chlorine based.– Do not use steel pads.– Avoid using cleaning products with...

8 Fig. 8 Burners and Grids – These parts can be removed and cleaned with appropriate products.– After cleaning, the burners and their flame spreaders must be well dried and correctly replaced. – It is very important to check that the burner flame spreader and the cap have been correctly positioned. ...

9 Correct Position of Triple Ring Burner The triple ring burner must be correctly positioned (see fig. 9); the burner ribs must be fitted in their housing as shown by the arrow.The burner correctly positioned must not rotate (fig. 10).Then position the cap “A” and the ring “B” (figs. 10 - 11) A B Fi...

11 Installation Technical Information for the Installer In order to install the hob into the kitchen fixture, a hole with the dimensions shown in fig. 12 has to be made, bearing in mind the following:– within the unit, between the bottom of the hob and the upper surface of a shelf there must be a cl...

12 Fastening the Installation Brackets (fig. 15) – Each hob is provided with an installation kit including brackets and screws for fastening the top to fixture panels from 2 to 4 cm thick. – Turn the hob upside down and fasten the brackets “A” to the appropriate socket holes, without tightening the ...

13 Gas supply requirements Important Note This appliance is supplied for use on NATURAL GAS or LPG (check the gas regulation label attached on the appliance).– Appliances supplied for use on NATURAL GAS: they are adjusted for this gas only and cannot be used on any other gas (LPG) without modificati...

14 Gas Connection The installation of the gas appliance to Natural Gas or LP Gas must be carried out by a suitably qualified and registered installer. Installers shall take due account of the provisions of the relevant British Standards Code of Practice, the Gas Safety Regulations and the Building S...

15 Gas connection Cat: II 2H3+ The fitting (fig. 17) is made up of:– 1 nut “A”– 1 elbow fitting “C”– gasket “F” Connection to the Gas Supply – Be careful when flexible pipes are used that they do not come into contact with moving parts.– To maintain the thickness of 3 cm, the hob is fitted with a ch...

16 Conversion to Natural Gas or LPG Replacing the Burner Injectors – Remove the pan supports, the burner caps and flame speaders.– Using a wrench, substitute the nozzle injectors “J” (Figs. 19 - 20) with those most suitable for the kind of gas for which it is to be used. The burners are conceived in...

17 Regulating the Burner Minimum Setting When changing from one type of gas to another, the minimum tap output must also be correct, considering that in this position the flame must be about 4 mm long and must remain lit even when the knob is turned sharply from the maximum to the minimum position. ...

18 Mains Electricity Connection Incorrect installation may be dangerous and the manufacturer can not be held responsible.Warning! This appliance must be earthed The manufacturer declines all responsibility for any problem caused by failure to observe this rule. THIS APPLIANCE MUST BE CONNECTED TO TH...

19 Appliance Servicing CDA provide a quality and effective after-sales service to cover all your servicing needs. Please attach your receipt to this page for safekeeping.Please help us to help you by having the following information available when booking a service-call:1. Model type, make and model...

Customer Car e Department • The G r oup Ltd. • Harby Road • Langar • Nottinghamshi r e • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : [email protected] W : www.cda.eu To contact our Customer Care Department, or for Service, please contact us on the details below. Cod. 1103520/GB - ß4