CDA CW493 BL/WH/SS - Manual

Page 4 - Safety Is Very Important; Low Salt Indicator Light; A B C D; Knob For Selecting Cycle

.1. IMPORTANT Carefully read the instructions contained in this manual, as it pro- vides information that is essential to safe and proper installation, use and maintenance of this appliance. This appliance complies with following EEC directives: -73/23/EEC of 19/02/73 (Low Voltage) and subsequent mo...

Page 5 - Technical Characteristics

.2. Close-up View (Interior) A B C D Upper Rack Rack Height Adjustor Top Spray Arm Lower Rack E F G H I Washing Filter Bottom Spray Arm Detergent and Rinse Aid Dispenser Technical Characteristics Width 60 cm Depth 58 cm Height 82 cm Capacity 12 standard place settings Mains water pressure 0.03-0.6 M...

Page 6 - To prevent the formation of rust, load the salt just before begin-; Adjusting Salt Consumption

.3. Salt...... Salt The hardness of the water varies from place to place. If hard water is used in the dishwasher, deposits will form on the dishes and utensils. The appliance is equipped with a special softener that uses a salt specifically designed to eliminate lime and minerals from the water. Lo...

Page 7 - tergent on the edges of the dispenser.; Rinse Aid; Proper dosage of the rinse aid improves drying.

.4. Detergent and Rinse Aid...... Detergent Detergent specifically intended for use with dishwashers must be used. The dispenser must be refilled before the start of each wash cycle following the instructions provided in the "Wash Cycle Table." The detergent dispenser is located on the insid...

Page 8 - Loading the Dishwasher

2 1 3 4 .5. Loading the Dishwasher Load for 12 Standard Settings Before placing the dishes in the dishwasher, remove larger food particles to prevent the filter from becoming clogged, which re- sults in reduced performance. If the pots and pans have baked-on food that is extremely hard to remove, we...

Page 11 - Wash Cycle Table; KKKKK; Normal Wash

.8. Wash Cycle Table Cycle Eco Button Rapid Button Cycle Selection Information Description of Cycle Deter- gent Rinse Aid I n t e n s i v e Wash I n t e n s i v e Wash N o r m a l Wash Rinse Glassware Glassware Soak Very dirty dishes, pots and pans (not to be used with delicate items). Very dirty di...

Page 13 - The special plastic hose support must be solidly fastened to the; Installation

.10. Installation Positioning the Appliance Position the appliance in the desired location. The back should rest against the wall behind it, and the sides, along the adjacent cabinets or wall. The dishwasher is equipped with water supply and drain hoses that can be positioned to the right or the lef...

Page 14 - Assembly Instructions for Integrated Dishwasher

Assembly Instructions for Integrated Dishwasher .11. The control panel can be easily aligned with the kitchen drawers, using the spacers supplied with the appliance (see Fig.1 and Fig.2).The height of the control panel is 115 mm, while the three spacers each add 7.5 mm in height. Technical Informati...

Page 15 - Installation of Continuous Base Moulding; If power screwdrivers are used to make the adjustment, make

Assembly Instructions for Integrated Dishwasher .12. The door must be perfectly balanced. In the factory , the tension of the springs is regulated to ensure that the door is perfectly balanced when light wood door panels are mounted on the door. If heavier, solid wood door panels are used, the door ...

Page 16 - NPTKR

Assembly Instructions for Integrated Dishwasher .13. Fig.1 Fig.2 Fig.6 NPTKR NNR Fig.5 Fig.3 Fig.4 mm 115 122.5 130 137.5 145 152.5 432mm 436mm440mm444mm LARGH.=448mm LARGH.=448mm 444mm440mm436mm432mm mm 115 122.5 130 137.5 145 152.5 582mm 586mm 590mm 594mm LARGH.=598mm mm 115 122.5 130 137.5 145 15...

Page 17 - SMM; UOM; RUM

Assembly Instructions for Integrated Dishwasher .14. Fig.7 Fig.8 Fig.10 ^ SMM UOM RUM Fig.9 SMMJTMM UM GB