Wayne Dalton 2411 - Manuals

Page 2 - OPERATING ZONE; You Can Save Time And Effort If You First Establish; All; The Facts About; HEADROOM CHART For Standard Lift Track

PG. 15 OPERATOR ARM(SUPPLIED BY OTHERS) CENTER HINGES 6” WELDED TRUSS 1/4-20 X 7/8”TEK SCREWS OPERATOR ARM(SUPPLIED BY OTHERS) 1-1/2” X 2-1/4” ANGLE(CUT TO FIT BETWEENSTRUT AND CENTERHINGE)(SUPPLIED BY OTHERS) Trolley installation for doors: < 9’ 2” All Heights9’ 3” thru 16’ 2” X 10’ 1” (5 sectio...

Page 3 - SIDEROOM REQUIREMENTS; inch TRACK; Steel Spring Pad Applications

PG. 3 DIM YHEADER TOSHAFTCENTERLINE MINIMUM HEADROOM REQUIRED(REFER TO ABOVE CHART) 8” for 2” TRACK 12” for 3” TRACK EXTEND JAMBS TO OPENING HEIGHT plus DIM Y plus 1 1/2” (MINIMUM LENGTH) TORSION SHAFTS REQUIRE 10” OF SIDEROOM FOR SOLID SHAFTS and 5” OF SIDEROOM FOR TUBULAR SHAFTS NOTE: HEADROOM CAN...

Page 4 - DO NOT GREASE THE INSIDE OF THE TRACK.; ” TRACK 1/4” GRADUATION

PG. 4 STEP 10: Attaching the Back Hanger Angles: Apply another locking pliers above the No. 2 or No. 3 rollerand then remove the locking pliers from the top roller. With assistance push downward on the door andremove all locking pliers. Carefully raise door until one and a half panels are in the hor...

Page 5 - ( Refer to the illustrations dependant on your track size); SPRING TURN CHART

3” TRACK 1/4” GRADUATION 9 SECTIONS HIGH OR LESS FIG.F FIG.I FIG.H FIG.G Align the appropriate end hinge to the pre-punched holes in the stiles and secure using (2) 1/4” x 5/8”self tapping screws per hinge. Products 16’2” wide and less require (1) end hinge (fig. D) and doors over16’2” wide require ...

Page 6 - Refer To Strutting Schedule Insert.

(2) 3/8” Nuts and Washers Top Plate Perimeter Seal Spring Mounting Pad. 2 x 6” White Pine or Denser. Secured with min. (4) 5/16” x 4” lag bolts into header. Header (2) 3/8” x 1” or 1-1/2” Bolts Pre-Cast Steel 1/2” x 3” Sleeve Anchor NOTE : Must secure sleeve anchors to building first then attach bra...

Page 7 - FOUR SPRINGS; TWO SPRINGS; Standard Strutting Schedule

PG. 7 PG. 10 FOUR SPRINGS (3-3/4” & 6”) (6” Shown) * NOTE: COUPLING USED ON SOLID SHAFT ONLY. TIGHTEN CONNECTING BOLTS AFTER WINDING SPRINGS. RED WINDING CONES AND CABLE DRUMS WILL ALWAYS BE ON THE LEFT BLACK (OR PLAIN) WINDING CONES AND CABLE DRUMS WILL ALWAYS BE ON THE RIGHT LOOKING FROM THE I...

Page 8 - TUBULAR OR 1 PIECE

PG. 9 PG. 8 STEP 8. Installing the Horizontal Track: Use chain or cable to suspend the rear of the horizontal tracks.Secure the horizontal reinforcing angle to the wall angle using (1) 3/8” x 3/4” truss bolt and nut, thensecure the horizontal track to the splice plate or flagangle using (2) track bo...

Page 16 - CONTENTS; repairs, or adjustments of this product be; IMPORTANT; SAFETY NOTICES; This manual; MAINTENANCE AND PAINTING INSTRUCTIONS; LIMITED WARRANTY; COMMERCIAL GARAGE DOOR; If in question about any of the procedures, Do Not perform the work.

® CONTENTS WARNING: It is recommended that installa-tion , repairs, or adjustments of this product be made by a qualified door agency. IMPORTANT An overhead door is a large heavy object that moves with the helpof springs under high tension. Moving objects and springs undertension can cause injuries....