Wayne Dalton 9700 - Manual
Wayne Dalton 9700 – Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – CAUTION; STEP 1: Drilling Lock Section
- Page 3 – STEP 2: Outside Lock Handle Assembly
- Page 4 – STEP 4: Installing The Auto Latch
Wayne-Dalton, a Division of
Overhead Door Corporation
P.O. Box 67, Mt. Hope, OH 44660
www.Wayne-Dalton.com
(2) #12 Pan head screws*
Part No: 307897
Outside handle
Inside door
handle
Release disk
(2) 1/4” - 20 x 1-3/4”
Self tapping screws
Retainer
nut
(6) 1/4” - 20 x 11/16”
Self drilling screws
Or 1/4” - 14 x 1” Lag
screws (Wood doors only)
(2) Auto latch
flipper
(2) Striker
plate
Washer 3/8” x 1”
REV6 01/25/2013
©Copyright 2013, Wayne-Dalton, a Division Of Overhead Door Corporation
(2)
Keys*
Rim cylinder*
Trim ring*
(4) #8 X 1/2” Pan
head screws*
Night latch
assembly*
Lock cable
(6) 1/4” - 20 x 9/16”
Track bolts
Rim Cylinder / Night Latch
Autolatch ECR Lock
Installation Instructions
and Owner’s Manual
All Residential Door Models: 5000, 9700, 9800,
8000 & 9000 Series & Wood Doors
TOOLS REQUIRED:
(1) Electric Drill
(1) 1/8” Drill Bit
(1) 3/4” Dia. Hole Saw
(1) 1-1/4” Dia. Hole Saw
(1) 7/16” 6 Point Nut Driver
(1) 7/16” Wrench Or Socket
(1) Pliers/Wire Cutter
(1) Phillips Screw Driver
(1) Standard Screw Driver
(1) Center Punch
IMPORTANT NOTICE!
REFER TO THE DOOR MODEL INSTALLATION INSTRUCTIONS MANUAL FOR
IMPORTANT SAFETY NOTICES.
Parts Breakdown
NOTE:
The illustrations shown on this page are general representations of
the door parts. Each specific door models may have unique variations.
Phillips head machine screws
(2) 1” (9100/5120/9800)
(2) 1-1/4” (8700/9400/9600/
5140/8300/8700/Wood)
(2) 1-1/2” (9700)
(2) 1-3/4” (8000/8100/8200/8500)
Lock backup plate
(8300/8500/8700/9700/9800/Wood)
Universal lock stile
(9100/9400/9600/5120/5140)
(2) Foam tape
(9100/9400/9600/5120/5140)
3/4” x 2-1/2”
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
2 DO NOT DRILL LOCK SECTION OR INSTALL LOCK ON DOORS WITH OPENERS. THE DOOR AND/ OR OPENER MAY BE DAMAGED IF THE OPENER IS USED WHILE THE DOOR IS LOCKED. NOTE: Common practice for doors with the odd number of raised panels is to mount the lock towards the right side of the section when looking out. ...
3 8000/8100/8200 DOORS, (SEE FIG. 4): Align the outside handle assembly with the handle pointing towards the floor and insert the assembly through the previously drilled 3/4” diameter holes in the section. Secure the outside lock handle to the section with (2) #10 phillips head screws. 5120/5140/610...
4 Locate the auto latch striker plates over the pre-punched holes in the vertical track nearest the center of the lock section. Fasten the striker plates to the vertical track using (2) 1/4” - 20 x 9/16” track bolts and flanged hex nuts. Align the auto latch flippers such that the arm will engage th...
