Wayne Dalton 900 - Manual

900 SERIES ROLLING SERVICE DOORS

1

900 SERIES

ROLLING SERVICE DOORS

GENERAL SPECIFICATIONS

FOR ROLLING SERVICE

DOORS

Note to Specifiers:

Words in parentheses indicate

frequently specified and highly

recommended options.

PART 1 GENERAL

1.01 Work Included—The opening

will be equipped with Wayne-

Dalton 900 Series rolling doors,

Model _____ as

manufactured by Wayne-Dalton

Corp.

1.02 Related Work—Opening

preparation, miscellaneous or

structural metal work, access

panels, finish or field painting, field

electrical wiring, wire, conduit,

fuses, and disconnect switches are

in the Scope of Work of other

divisions or trades.

PART 2 PRODUCT

2.01 Curtain will be composed of

prime painted galvanized steel

interlocking slats (A) gauge, No.

(B) slats, roll-formed from (C)

per ASTM standards and designed

to withstand a 20 PSF windload.

Ends of alternate slats will be fitted

with metal endlocks/windlocks.

Bottom Bar will consist of 2 equal

galvanized steel (stainless

steel) angles, (aluminum

extrusion) minimum

1

¼

8

"

th

ic

k,

t

o

stiffen curtain with neoprene loop

astragal. When required for

additional security, provide (slide

bolts) (cylinder locks) on the

bottom bar operable from (coil

side) (opposite coil side)

(both sides).

2.02 Guides will be of roll-formed

galvanized steel channels and

angles (three angle assembly)

of steel (stainless steel)

(aluminum) to form a slot of

sufficient depth to retain curtains in

guides to resist 20 PSF windload.

Guides may be provided with

integral windlock bars and

removable bottom bar stops.

2.03 Brackets will be of galvanized

steel plates with permanently

sealed ball bearings. Designed to

enclose ends of coil and provide

support for counterbalance pipe at

each end.

2.04 Counterbalance: Curtain to

be coiled on a pipe of sufficient

size to carry door load with

deflection not to exceed .03 inches

per foot of door span and to be

evenly balanced by helical springs,

oil tempered torsion type designed

with a 25% safety factor. Cast iron

barrel plugs will be used to anchor

springs to tension shaft and pipe.

2.05 Hood will be minimum 24

gauge (prime painted

galvanized) (galvanized)

(slatted) steel, flanged at top for

attachment to header and flanged

at bottom to provide longitudinal

stiffness. Hood will enclose curtain

coil and counterbalance

mechanism.

2.06 Finish: Shop coat of rust

inhibitive primer on non-galvanized

surfaces and operating

mechanisms. Aluminum finish to

be (mill) (204R1 clear

anodized) (bronze anodized).

Stainless steel finish to be (#4).

Curtain will be (white) (blue)

(gray) (tan) (brown).

2.07 Operation: Door will be

operated by means of (manual,

push-up) (chain hoist with gear

drive reduction) (awning

crank) (wall crank box)

(motor operation). (Electrical)

(Pneumatic) sensing edge to be

attached to bottom bar to (stop)

(stop and reverse) the door

when it contacts an object during

the closing cycle.

2.08 Weatherstripping: Air-

Bar/Extr-Tite doors will include flat

slats, bottom astragal, exterior

surface guide weatherstrip, and

internal hood baffle weatherstrip.

2.09 Locking: (Manual push-up

doors will have interior slide-bolts

suitable for padlocks by others.)

(Chain-hoist door will have chain

keepers suitable for padlocks by

others.) (Electric-motor

operation doors will lock through

the operator gearing.) (Cylinder

locks can be provided with the

doors.)

CAUTION: When specifying

cylinder locks on electric-motor

operated doors, electric interlocks

should also be specified to prevent

operation when lock bolts are

engaged in the guides, thus

preventing damage to the curtain

and/or operator.

PART 3 EXECUTION

3.01 Install the doors in

accordance with Wayne-Dalton

Corp. instructions and standards.

Installation and maintenance will

be by an authorized Wayne-Dalton

representative.

Because of continuing product improvements, we reserve the

right to change the product specifications and designs without

prior notice.

WAYNE-DALTON CORP. • ONE

DOOR

DRIVE • MT. HOPE, OH 44660 • PH. 800-764-1457 • FX. 800-336-

1422

For easier door specifications or product questions call the WayneTec Consulting Service

1

-8

0

0

-76
4

-1

4

57
.

COLORS INCLUDE:

(22 and 24 gauge

only)

White

Blue

Gray

Tan

Brown

©2001 Wayne-Dalton Corp.

Rev. 11/01 246570