Vision Fitness ST700 - Manuals

Page 3 - T a b l e o f C o n t e n t s

3 ASSEMBLY GUIDE . . . . . . . . . . . . . . . . 4HARDWARE BAGS . . . . . . . . . . . . . . . . 6STEP 1: ORANGE BAG . . . . . . . . . . . . . 9STEP 2: BLUE BAG . . . . . . . . . . . . . . . 10STEP 3: PINK BAG . . . . . . . . . . . . . . . 11STEP 4: GREEN BAG . . . . . . . . . . . . . . 12STEP 5: CAB...

Page 4 - O w n e r ’ s G u i d e

4 To avoid possible damage to this Functional Trainer, please follow these assembly steps in the correct order. Before proceeding, find your new Functional Trainer serial number located on the side of the right floor support (AC3), andenter here: Refer to this number when calling for service, and en...

Page 6 - H A R D WA R E I N C L U D E D

O R A N G E B A G 6 B L U E B A G H A R D WA R E I N C L U D E D M10 Nylon Nut Quantity: 8 10.2 x 22 x 2 Flat Washer Quantity: 21 M10 Nylon Nut Quantity: 4 M10 x 70 Bolt Quantity: 8 10.2 x 18.4 x 2.5 Lock WasherQuantity: 13 M10 x 70 Bolt Quantity: 5 M10 Acorn Nut Quantity: 12 10.2 x 22 x 2 Flat Wash...

Page 9 - O R A N G E B A G

9 AC1 AC1 AC2 AC2 AC3 AC3 1 S T E P NOTE: During assembly, it is recommendedto ensure that all bolts are in place and partially threaded before completely tighteningany one bolt. During assembly steps 1 thru4, do not completely tighten any bolts untilcompletion of Step 4. • Lay the center floor supp...

Page 10 - B L U E B A G

10 2 S T E P B L U E B A G AD2 AQ1 Q18 Weight Storage Post • Place the chrome front upright (AG1)over the protruding bolt ends on front ofleft floor support (AC2), making sure num-bers and holes are facing outward.Secure using a flat washer (10.2x22x2),lock washer (10.2x18.4x2.5), and anacorn nut (M...

Page 11 - P I N K B A G

11 3 S T E P • Place the top left frame (AB4) on the leftside uprights (AG1 & AG2), with the protruding bolt ends going through holesin the left rear upright (AG2). Slide a flatwasher (10.2x22x2) and lock washer(10.2x18.4x2.5) over each bolt end, andsecure with an acorn nut (M10). Securetwo bolt...

Page 12 - G R E E N B A G

12 4 S T E P • Place the two rubber bumpers (Q05)over the holes for the guide rods in centerfloor support (AC1). With the horizontalholes at the bottom, slide the guide rodsthrough the rubber bumpers and into centerfloor support. Let the guide rods tilt forward.Slide each of the 15 weight plates ove...

Page 17 - B L A C K B A G

17 9 S T E P • Slide the slip-on nuts (B26) over the holesof the connecting brackets (Z19). Attach thetwo connecting brackets (Z19) to the insideof the right shield (Q02) with two bolts(M5x10). Make sure the brackets are posi-tioned parallel to the floor when tightened.Loosely fasten the right shiel...

Page 18 - Y E L L O W B A G

18 10 S T E P Secure the foot plate (E07) to the centerfloor support using two bolts (M10x25),two lock washers (10.2x18.4x2.5) andtwo flat washers (10.2x22x2). Y E L L O W B A G

Page 19 - E F F E C T I V E R E S I S TA N C E

19 E F F E C T I V E R E S I S TA N C E 50% 50% 100% W e i g h t S t a c k 5 0 % 1 0 0 % 1 0 5 1 0 1 5 7 . 5 1 5 2 0 1 0 2 0 2 5 1 2 . 5 2 5 3 0 1 5 3 0 3 5 1 7 . 5 3 5 4 0 2 0 4 0 4 5 2 2 . 5 4 5 5 0 2 5 5 0 5 5 2 7 . 5 5 5 6 0 3 0 6 0 6 5 3 2 . 5 6 5 7 0 3 5 7 0 7 5 3 7 . 5 7 5 8 0 4 0 8 0 8 5 4 2...

Page 24 - I N C L U D E D A C C E S S O R I E S

24 Dual-Swivel Bar Quantity: 1 Foot Cuff Quantity: 2 Co-Molded Handle Quantity: 2 Sport Handle Quantity: 1 5# Add-on Weight Quantity: 1 I N C L U D E D A C C E S S O R I E S

Page 32 - I T E M

32 MAINTENANCE SCHEDULE FOR BEST PERFORMANCE WE RECOMMEND THE FOLLOWING MAINTENANCE SCHEDULE: Check the integrity and function of the following parts. Replace all worn components immediately. DAILY WEEKLY I T E M CABLES CHECK END FITTINGS AND CABLE JACKET COATING. CHECK TIGHTNESS OF WEIGHT STACK LOC...

Page 40 - s t a r t s; v i s i o n; w i t h a

5 0 0 S o u t h C P A v e n u e • P. O . B o x 2 8 0 • L a k e M i l l s . W I 5 3 5 5 1 t o l l f r e e 8 0 0 . 3 3 5 . 4 3 4 8 • p h o n e 9 2 0 . 6 4 8 . 4 0 9 0 • f a x 9 2 0 . 6 4 8 . 3 3 7 3 w w w. v i s i o n f i t n e s s . c o m © 2 0 0 7 V i s i o n F i t n e s s . A l l R i g h t s R e s ...