Vision Fitness ST200 - Manuals

Vision Fitness ST200 – Manual in PDF format online.

Manuals:

Manual

Manual Vision Fitness ST200

Summary

Page 4 - T O O L S & P A R T S I N C L U D E D; P A R T S B O X

4 19mm Wrench 6mm L-Shaped Wrench T O O L S & P A R T S I N C L U D E D P A R T S B O X Color-coded Hardware Bags Owner’s Guide Assembly Guide Warranty Card 10mm/17mm Wrench 4mm L-Shaped Wrench

Page 5 - H A R D WA R E I N C L U D E D

5 O R A N G E B A G B L U E B A G H A R D WA R E I N C L U D E D SW10.2 x 18.4 x 2.5T Spring Washer Quantity: 4 10.5 x 18 x 2T Flat Washer Quantity: 8 M10 x 1.5P Nut Quantity: 6 M10 x 1.5P x 60L Bolt Quantity: 4 M10 x 1.5P x 25L Bolt Quantity: 2 M6 x 1P x 15L Bolt Quantity: 2 M10 x 1.5P x 60L Bolt Q...

Page 8 - R E D B A G

8 R E D B A G H A R D WA R E I N C L U D E D SW10.2 x 18.4 x 2.5T Spring Washer Quantity: 10 M10 x 1.5P x 25L Bolt Quantity: 10

Page 9 - O R A N G E B A G

9 1d 1b 1e 1c 1a 1 S T E P • Lay the back side of the rear verticalupright (1a) down onto the floor. Thethreaded bolt ends will be pointing up.Place the center floor support (1b) over thethreaded ends. Attach a flat (10.5x18x2T)and spring (SW10.2x18.4x2.5T) washerand nut (M10x1.5P) to each end. Tipu...

Page 10 - B L U E B A G

10 2 S T E P • Thread pull pins partially onto 2a (Qty. 1)and 2c (Qty. 2). • Lay the front center vertical (2f) on thefloor. Slide the seat support structure (2a)over the open end of 2f. NOTE: You must pull the pull pin out (2b) and hold it whensliding over 2f. Release and engage the pull pin in one...

Page 11 - P I N K B A G

11 3 S T E P • Place the top front structure (3a) on topof 2f and attach with two bolts(M10x1.5Px60L), two flat (10.5x18x2T)washers, and two nuts (M10x1.5P).Tighten fasteners with a 6mm L-shapedwrench and a 17mm wrench. • Attach the seat (3b) up through the bottom of 2a with four bolts(M10x1.5Px25L)...

Page 12 - G R E E N B A G

12 4 S T E P • Place the bottom of the left oval upright(4a) onto the protruding bolts of 1d. NOTE: Make sure the 27 holes of 4a areon the outside. Mate the hole in the top of 4a with the top hole of 3a. Attach andtighten one flat (10x30x2T) & spring(SW10.2x18.4x2.5T) washer and onebolt (M10x1.5...

Page 13 - B L A C K B A G

13 5 S T E P • If you are adding 15 weight plates to thebase unit, proceed as follows. If you areadding 20 weight plates, the steel tubespacer (5a) will not be used. • Place two rubber weight plate bumpers(5b) over the 0.75” holes of 5a. Place 5aover the holes of 1b. With the horizontalholes at the ...

Page 14 - Y E L L O W B A G

14 6 S T E P Wrap one end of cable #1 around pulleyA. On the right side of the unit, place itthrough pulleys B, C, D of 6a, and E.Remove the nuts from 2 slotted bolts (M12)(see diagram below). With the threadspointing down on the slotted bolt (M12),slide the end of cable #1 through it.Reattach the n...

Page 16 - Y E L L O W B A G

16 8 S T E P • Remove the slotted bolts (8a) located onthe inside of the right and left handles ofuprights 4a & 4b. Remove the nuts fromthe bolts. Slide the small steel end of cable#3 through pulleys H & I. Continuethrough pulleys J thru P. Slide the cablethrough the slotted bolt so that the...

Page 17 - R E D B A G

17 9 S T E P • Place the rear hole of the left decorativecover (9a) over the threaded post on theleft side of structure 5e. Loosely attach aspring (SW10.2x18.4x2.5T) washer anda bolt (M10x1.5Px25L). Thread two bolts(M10x1.5Px25L) and two spring(SW10.2x18.4x2.5T) washers into thetwo front holes. Tigh...

Page 18 - D E C A L S

18 General Warning/Safety Decal Placement Weight Plate Sticker Placement 1 0 S T E P • Attach the decals according to the diagram below. D E C A L S

Page 20 - s t a r t s; v i s i o n; w i t h a

5 0 0 S o u t h C P A v e n u e • P. O . B o x 2 8 0 • L a k e M i l l s . W I 5 3 5 5 1 t o l l f r e e 8 0 0 . 3 3 5 . 4 3 4 8 • p h o n e 9 2 0 . 6 4 8 . 4 0 9 0 • f a x 9 2 0 . 6 4 8 . 3 3 7 3 w w w. v i s i o n f i t n e s s . c o m © 2 0 0 5 V i s i o n F i t n e s s . A l l R i g h t s R e s ...