Thermo Pride OH5-85DXE - Manuals

Page 2 - This furnace is not to be used as a construction heater.

i I. SAFETY SECTION This page contains various warnings and cautions found throughout the Oil Furnace Manual. Please read and comply with the statements below. c WARNING AND CAUTIONS: c WARNING: This furnace is not to be used as a construction heater. See Page 1. c CAUTION MUST BE TAKEN NOT TO EXCEE...

Page 3 - ii; TABLE OF CONTENTS

All installations and services must be performed by qualified service personnel. ii TABLE OF CONTENTS SECTION BEGINNING PAGE I. SAFETY SECTION i II. GENERAL INSTRUCTIONS 1 A. VENTING 2 B. DRAFT REGULATORS 2 C. DUCT WORK/AIR CONDITIONING 3 D. FILTERS MOUNTED EXTERNAL TO FURNACE 3 E. LIMIT POSITION AN...

Page 5 - Then, by following the dimensions listed below,; UNIT

All installations and services must be performed by qualified service personnel. 2 A. VENTING: NOTE: On the OH5-85DXE*** it is possible to rotate the flue elbow (which is factory installed for vertical discharge) 90° counterclockwise from the vertical position to adapt to various venting systems. c ...

Page 6 - specified otherwise by the individual coil manufacturer.; highboy

All installations and services must be performed by qualified service personnel. 3 C. DUCT WORK/AIR CONDITIONING: If the furnace is used in connection with summer air conditioning (cooling), the furnace should be installed parallel with or on the upstream side of the evaporator coil to avoid condens...

Page 7 - When cutting openings in the casing; DO NOT CUT ANY SUPPORTING; Fig. 6: Cutaway view of fan section of a typical highboy furnace.

All installations and services must be performed by qualified service personnel. 4 Connect the return air plenum to the filter rack and slide the filter into place. Dimensions for adapting the return air plenum to the filter rack are provided (See Fig. 5). Fig. 5: A typical filter rack and dimension...

Page 9 - Do not place loose insulation around chamber sides and back .

All installations and services must be performed by qualified service personnel. 6 Fig. 9: (Top view) Burner insertion illustration When mounting the burner, the upper mounting plate (Fig. 8) must be removed to provide access to the area in front of the combustion chamber. The combustion chamber can...

Page 10 - RIELLO BURNER APPLICATION CHART; STAGE FIRING RATES; NOZZLE SIZE; HIGH FIRE

All installations and services must be performed by qualified service personnel. 7 G. BURNER SPECIFICATIONS AND APPLICATIONS RIELLO BURNER APPLICATION CHART MODEL PART OH5 2 STAGE MTG. PLATE PART NO. 35750 MTG. PLATE GASKET PART NO. 330088 **NOZZLE SIZE .70 X 45 ° W NOZZLE PART NO. 380702 OIL PUMP P...

Page 11 - WARNING: THE HEAT EXCHANGER MUST BE CLEANED BY A QUALIFIED; This panel is identified with a label.

All installations and services must be performed by qualified service personnel. 8 H. HEAT EXCHANGER CLEANING INSTRUCTIONS: c WARNING: THE HEAT EXCHANGER MUST BE CLEANED BY A QUALIFIED SERVICE PERSON. It is important to inspect and clean the heat exchanger once a year, or as necessary, to remove any...

Page 12 - EXTERIOR OF FURNACE:; discoloration of materials and damage from rust or corrosion.; CHIMNEY OR VENTING SYSTEM:; The furnace venting system should be inspected for signs of rust,

All installations and services must be performed by qualified service personnel. 9 Reassemble the furnace to its original construction. Remount the burner being certain that the air tube is properly inserted into the chamber opening (see section E). If heavy soot deposits were found in the heat exch...

Page 13 - Fig. 18: Location of the air filter on the typical highboy furnace.

All installations and services must be performed by qualified service personnel. 10 4. Turn service switch to furnace "ON". If burner starts and runs, but stops again on lockout, it may be necessary to bleed the lines or make burner combustion air adjustments. Contact a qualified service per...

Page 14 - CUSTOMER; COMBUSTION

All installations and services must be performed by qualified service personnel. 11 COMBUSTION AND EFFICIENCY TESTING FOR THERMO PRIDE OIL FIRED CENTRAL FURNACES. Complete this form for each Thermo Pride furnace installed. Read instruction CUSTOMER NAME ADDRESS CITY, STATE HEATING SYSTEM BURNER MODE...

Page 15 - APPENDIX-A Replacement Parts List

All installations and services must be performed by qualified service personnel. 12 APPENDIX-A Replacement Parts List

Page 16 - APPENDIX-B Wiring Diagram

All installations and services must be performed by qualified service personnel. 13 APPENDIX-B Wiring Diagram