Thermo Pride CMA2-75N - Manuals

All installations and services must be performed by qualified service personnel. accordance with the latest edition of the UL Standard for Single and Multiple Station Carbon Monoxide Alarms, UL 2034, or the CSA International Standard, Residential Carbon Monoxide Alarming Devises, CSA 6.19. 5. The in...

All installations and services must be performed by qualified service personnel. MODELS CMA CLOSET ALCOVE FRONT BACK SIDES VENT CONNECTOR(PVC) TOP PLENUM SIDES TOP AND SIDES OF DUCT BOTTOM OF DUCT 6” 0” 0” 0” 0” 1” 1” 1” 18” 0” 0” 0” 0” 1” 1” 1” Table 1 This heating appliance must be installed with ...

All installations and services must be performed by qualified service personnel. Combustible Floor Base Model: 70-BASE Figure 1A. Coil Cabinet Model: CE113S Note: This cabinet cannot be utilized as a cottage base. Figure 1B. 10

All installations and services must be performed by qualified service personnel. connector duct. Remove the bottom panel. Cut an opening in the distribution duct slightly larger than the connector duct. (refer to Figure 2 for location of this cut.) Cut the connector duct to length. Install the conne...

All installations and services must be performed by qualified service personnel. D. CLOSET INSTALLATION 1. The return air opening into the closet is to have a minimum free area of 250 sq. in. (see Figure 5). 2. The return air opening may be located in the top, center or (ideally) bottom of the close...

All installations and services must be performed by qualified service personnel. : The furnace and its gas valve must be disconnected from the gas supply during pressure testing of the gas supply system at pressures in excess of 1/2 PSIG or 14 inches w.c F. GENERAL VENTING REQUIREMENTS The CMA furna...

All installations and services must be performed by qualified service personnel. MAXIMUM VENT LENGTH VENT SIZE 2 IN. PVC FURNACE MODEL VENT LENGTH (FT.) EXHAUST VENT ELBOWS (NO.) COMBUSTION AIR INTAKE ELBOWS (NO.) CMA 30 8* 7** *Note the drain elbow supplied with CMA furnaces count as 1 elbow. **Not...

All installations and services must be performed by qualified service personnel. G. CONNECTING THE EXHAUST VENT AND COMBUSTION AIR INTAKE Figure 6. shows the typical exhaust vent and combustion air intake connection for CMA furnace. Figure 6. (CMA*-75 SHOWN) NOTICE: The exhaust vent pipe must be sup...

All installations and services must be performed by qualified service personnel. NOTICE: The furnace model series CMA may be vented either through the sidewall or the roof. For sidewall instructions, continue to the following section. For roof venting, refer to Section IV J, of this manual. NOTICE: ...

All installations and services must be performed by qualified service personnel. Figure 7: Proper Direct Vent Terminations (RH & LH views) and Vent Termination Only w/o Outside Combustion Air Intake (RH view) NOTICE: If exterior sidewall building materials are subject to degradation from contact...

All installations and services must be performed by qualified service personnel. Figure 8: Typical Relative Locations of Direct Vent Terminations When Sidewall Venting 3. Exhaust Vent Terminal Location Clearance Requirements a. The vent terminal shall be located at least 3-feet above any forced air ...

All installations and services must be performed by qualified service personnel. Figure 9: NFGC Minimum Clearances Between the Vent Terminal and Various Building Features 22

All installations and services must be performed by qualified service personnel. 4. Vent Terminal Location Guidelines : Bushes, shrubs, or any vegetation that may restrict the flow of flue products must be kept away from vent and air intake terminations. Terminations must also be kept clear of any l...

All installations and services must be performed by qualified service personnel. inlet as shown in Figure 10, making sure that the spacing between the inlet and outlet complies with that noted in Figure 8. Figure 10: Typical Construction Details of Sidewall Vent and Air Intake Terminations 3. Finish...

All installations and services must be performed by qualified service personnel. 3. An optional condensate pump (P/N 350225) is available. This pump will not fit into the vestibule of the furnace and must be installed below the furnace for operation. Instructions will be included with pump if this o...

All installations and services must be performed by qualified service personnel. NOTE: Class 1 thermostat wire must be used inside the furnace burner compartment. a. Insert 24 VAC wires through the plastic grommet on the left side of the furnace casing. b. Connect the thermostat wires to the W/R 50A...

All installations and services must be performed by qualified service personnel. mounted junction box. The hot leg must pass through the disconnect switch in all cases to prevent the hazard of electrical shock when servicing. IMPORTANT: The furnace must be grounded in accordance with local codes and...

All installations and services must be performed by qualified service personnel. CMA1-50 ALTERATIONS REQ’D FOR A/C @ DESIGN EXTERNAL STATIC PRESSURE COOLING UNIT HTG Speed Recommended CLG Speed 24,000 LOW MED-LOW 30,000 LOW MED-HIGH 36,000 LOW HIGH Furnace Airflow (CFM) vs. External Static pressure ...

All installations and services must be performed by qualified service personnel. C. ADJUSTMENT OF BTU INPUT RATE: The orifice for this furnace was sized: 1) for natural gas having a heating value of 1025 BTU per cubic foot and a specific gravity of .65, or 2) for liquefied propane gas with a heating...

All installations and services must be performed by qualified service personnel. flames should be clear, blue and almost transparent in color. (see Figure 16). NOTE: It is not unusual to have orangish flames visible in the tube for LP gas. Figure 16. : The CMA furnace models are direct vent design a...

All installations and services must be performed by qualified service personnel. control, with one of the higher speed blower leads attached to a terminal marked “Park”. Be sure to attach any unused blower leads to a terminal marked “Park”. Replace the blower door and turn on the power supply. F. FU...

All installations and services must be performed by qualified service personnel. A. ELECTRICAL: 1. Check diagnostic code through view port prior to removing access door. 2. Check all wiring for loose connections and any signs of damage or unusual wear. 3. Check for correct voltage at the furnace whe...

All installations and services must be performed by qualified service personnel. 5. GASKETS/SEALING MATERIALS Inspect all visible gaskets for signs of degradation or liquid seepage, especially any seals which were removed as part of the inspection. Replace any suspect gaskets. C. HEAT EXCHANGER Insp...

All installations and services must be performed by qualified service personnel. FILTER MAINTENANCE PROCEDURE The filter is located inside front door of the CMA. Remove filter retaining rod and remove dirty filter. Clean the filter by vacuuming, rinsing with tap water, hosing or dipping in an ordina...

All installations and services must be performed by qualified service personnel. 3 flashes, then pause pressure switch stuck open 4 flashes, then pause open high limit switch 6 flashes, then pause 115 volt AC power reversed 7 flashes, then pause low flame sense signal 8 flashes, then pause check ign...

All installations and services must be performed by qualified service personnel. APPENDIX – A REPLACEMENT PARTS 50

All installations and services must be performed by qualified service personnel. APPENDIX – B WIRING DIAGRAM 52