Smeg WM40T-1- Manuals

Page 3 - SECTION 2: INSTALLATION; REMOVAL OF TRANSPORTATION SCREWS; Do not install your machine on rugs or similar surfaces.

• If you will not use your machine for a long time, unplug your machine, close the water supply and leave the door open in order to keep the inside of the machine dry and for prevention from unpleasant odour. • As a result of the quality control procedures, a certain amount of water may remain in yo...

Page 4 - ELECTRICAL CONNECTION; Be sure that water inlet hoses are not folded, broken or crushed.

• You can adjust the balance of your machine from its feet. • First, loosen the plastic adjustment nut. • Adjust by rotating the feet upwards or downwards. • After the balance has been reached, tighten the plastic adjustment nut again by rotating it upwards. • Never put cartons, wooden blocks or sim...

Page 5 - Cold water inlet; WATER DRAIN CONNECTION; Never attempt to extend the water drain hose by adding extra parts.

Cold water inlet WATER DRAIN CONNECTION • Be sure that water inlet hoses are not folded, twisted, crushed or elongated by stretching. • Water drain hose should be mounted at a height of minimum 60 cm, maximum 100 cm from the ground. • The end of the water drain hose may directly be fitted to the dir...

Page 7 - SECTION 4:CONTROL PANEL

SECTION 4:CONTROL PANEL WM40T-1 1 2 3 4 5 6 7 8 9 1-Detergent drawer 6-Program knob 2-Start/pause light 7-Start/pause button 3-Function indicator lights 8-Function buttons 4-Temperature adjustment knob 9-Program end light 5-Program ready light 34

Page 9 - TEMPARATURE ADJUSTMENT KNOB; PROGRAM KNOB

WARNING! F unctions vary depending on the model you have chosen.If you forgot to use additional function and your machine starts to wash push the additional function button if the indicator light is on. Additional function will be activated.If the indicator light is not on,additional function will n...

Page 10 - SECTION 5: WASHING YOUR LAUNDRY; First wash cycle

1-Cotton 90°C 2- Cotton 60°C with prewash 3- Cotton 60°C 4- Cotton 40°C 5- Eco wash 6- Quick wash 7- Cotton cold 8- Synthetic 60°C 9- Synthetic 40°C 10- Synthetic cold 11- Delicate 30°C 12- Wool 30°C Rinsing Spin Draining OFF SECTION 5: WASHING YOUR LAUNDRY • Plug the machine. • Open the tap water. ...

Page 16 - Danger of being scalded!; Since the water inside the pump maybe hot, wait for it to cool.; DETERGENT DRAWER; Wash will an old toothbrush and excessiveamount of water.

WARNING! Danger of being scalded! Since the water inside the pump maybe hot, wait for it to cool. DETERGENT DRAWER Detergents may form a sediment in your detergent drawer or in housing of the detergent drawer in time. To clean the sediment, pull out the detergent drawer from time to time.To pull out...

Page 17 - SIPHON PLUG; Plug in the machine.; THE DRUM; REMOVE OF LIME FROM YOUR MACHINE

SIPHON PLUG Pull out the detrgent drawer. Remove the siphon plug and clean the residues of the softener thoroughly. Fit the cleaned siphon plug in its location. Check if it placed properly. THE CABINET Clean the exterior surface of the cabinet of your machine with lukewarm water and a cleaning subst...

Page 19 - Remove the water inlet hose.; PUMP FILTER; Remove the foreign materials from the filter.

• Remove the water inlet hose. • Remove the filters found on the water inlet valves by using a pincer and wash thoroughly with a brush. • Clean the filters of the water inlet hoses located on the tap side by removing manually together with the seal. • After you clean the filters, you can fit them th...

Page 20 - Mould; SECTION 8: AVOIDING MINOR FAULTS

Mould : Mould stains should be cleaned as soon as possible. The stain should be washed with detergent, and if it does not disappear, it should be wiped with oxygenated water (in proportion of 3%). Ink: Hold the stained area under cold water and wait until the inky water completely runs off. Then rub...

Page 21 - Your fuse is defected.

FAILURE PROBABLE CAUSE METHODS OF ELIMINATION It is unplugged. Insert the plug into the socket. Your fuse is defected. Change your fuse. The electric power is off. Check the electric power. Start/pause button has not been pressed. Press the start/pause button. The program knob is in O(off) status. B...

Page 24 - SECTION 9: AUTOMATIC FAILURE DETECTION SYSTEM

FAILURE PROBABLE CAUSE METHODS OF ELIMINATION The spining process is not done or starts with delay . No failure. The unbalanced load control may works in that way. The unbalanced load control system will try to distribute your clothes in a homogenous manner. After your clothes are distributed, passa...

Page 27 - SECTION 10: INTERNATIONAL WASHING SIGNS; Washing

SECTION 10: INTERNATIONAL WASHING SIGNS Washing temparature. Do not wash (hand wash) Lukewarm iron. Medium hot iron. Hot iron. Do not iron. Do not tumble dry. Hang to dry. Drip dry. Dry flat. Do not bleach. Handy to bleach. All of these are dry cleaning symbols. The letters are to instruct the clean...