Smeg BQ6030- Manual
Smeg BQ6030– Manual, read for free online in PDF format. We hope this helps you resolve any issues you may have. If you have further questions, please contact us through the contact form.
Table of Contents:
- Page 2 – Instructions for the Installer; CONNECTION TO THE MAINS GAS SUPPLY; Check that all the conditions listed below are met:; tight bends or kinks in it.; do not attempt; • check that the hose's expiration date has not been passed.
- Page 3 – BURNER, NOZZLE AND GAS CONSUMPTION DATA TABLES; In the
- Page 4 – CHANGING THE NOZZLES; REPLACING THE BURNER SECTION NOZZLES; Remove the burners from the barbecue section.
- Page 5 – ADJUSTING THE PRIMARY AIR FLOWS
- Page 6 – ADJUSTING THE BURNER MINIMUM SETTING; CONVERTING FROM LPG TO NATURAL GAS; Turn the bypass as stated in the; BURNER; setting; CONVERTING FROM NATURAL GAS TO LPG.
9
Instructions for the Installer
CONVERSION INSTRUCTIONS
CONTENTS OF THE KIT
THIS MANUAL IS AN INTEGRAL PART OF THE APPLIANCE. TAKE GOOD CARE
OF IT AND KEEP IT TO HAND THROUGHOUT THE APPLIANCE'S LIFE CYCLE.
INSTALLATION MUST BE CARRIED OUT BY QUALIFIED STAFF IN
COMPLIANCE WITH THE RELEVANT REGULATIONS. THE MANUFACTURER
DECLINES ALL LIABILITY FOR IMPROPER USES OTHER THAN THOSE
STATED ABOVE.
This kit, for separate sale, has been specially designed to convert the
barbecue from
LPG
to
NATURAL GAS
.
It contains all the components and instructions necessary for the
conversion procedure.
The appliance is set in the factory to operate on
LPG
. The conversion
procedure (requiring the kit described below) involves replacement of all
the burner nozzles, adjustment of the primary air flow of the barbecue
section burners only, and adjustment of the minimum flame setting on the
gas taps.
On completion of these operations, replace the “regulated for gas” label on
the rear of the barbecue with the one supplied in the kit.
The installation work must be carried out by a skilled technician.
WARNING:
Keep all the nozzles factory-fitted on the appliance, the union
supplied and the “regulated for gas” label. It might be necessary to convert
the appliance back from
NATURAL GAS
to
LPG
in the future.
When converting back to
LPG
the conversion procedure is exactly the
same as that described below for
NATURAL GAS
.
The contents of the natural gas conversion kit are listed below:
•
NATURAL GAS NOZZLES.
•
5/8" TO 1/2" GAS MALE UNION.
• SEAL.
•
"REGULATED FOR" LABEL
(TO BE APPLIED AFTER CONVERSION).
"Loading the manual" means you need to wait until the file loads and becomes available for online reading. Some manuals are very large, and the time they take to appear depends on your internet speed.
Summary
10 Instructions for the Installer CONNECTION TO THE MAINS GAS SUPPLY Connect the appliance to the mainsnatural gas supply using a rubber orsteel hose in accordance with therelevant regulations.Screw the 5/8”-1/2” union ( B ) supplied onto the barbecue's gasinlet ( C ). Screw the union ( A ) onto the...
11 Instructions for the Installer BURNER, NOZZLE AND GAS CONSUMPTION DATA TABLES Burner Rated heat capacity (kW) Bottled gas – G30/G31 30/37 mbar n. turns by-pass Nozzle diameter 1/100 mm By-pass 1/100 mm Reduced heat capacity (W) Capacity g/h G30 Capacity g/h G31 Left 4.5 closed 100 85 2200 327 321...
12 Instructions for the Installer CHANGING THE NOZZLES REPLACING THE BURNER SECTION NOZZLES 1 Remove the grids and refractory plates inside thebarbecue section. 2 Undo the screws (for each burner) on the rearcross-member. 3 Remove the burners from the barbecue section. 4 Using a 7 mm socket wrench, ...
