Smeg PV175CB- Manuals

Description 29 EN 2 Description 2.1 General Description 60 cm 70 cm AUX = AuxiliarySR = Semi-rapidRR = Reduced rapid R1= Large rapidR2 = Medium rapid

Description 30 2.2 Symbols Cooking zones Front left Rear left Central Rear right Front right Centre left Burner knobs Useful for lighting and adjusting the hob burners. Press and turn the knobs anti- clockwise to the value to light the relative burners. Turn the knobs to the zone between the maximum...

Use 31 EN 3 Use 3.1 Instructions 3.2 First use 1. Remove any protective film from the outside or inside of the appliance, including accessories. 2. Remove any labels (apart from the technical data plate) from accessories. 3. Remove and wash all the appliance accessories (see 4 Cleaning and maintenan...

Use 32 3.3 Using the hob All the appliance's control and monitoring devices are located together on the front panel. The burner controlled by each knob is shown next to the knob. The appliance is equipped with an electronic ignition device. Simply press the knob and turn it anti-clockwise to the max...

Use 33 EN Practical tips for using the hob For better burner efficiency and to minimise gas consumption, use pans with lids and of suitable size for the burner, so that flames do not reach up the sides of the pan. Once the contents come to the boil, turn down the flame far enough to ensure that the ...

Cleaning and maintenance 34 4 Cleaning and maintenance 4.1 Instructions 4.2 Cleaning the appliance To keep the surfaces in good condition, they should be cleaned regularly after use. Let them cool first. Ordinary daily cleaning Always use only specific products that do not contain abrasives or chlor...

Cleaning and maintenance 35 EN Cooking hob grids Remove the grids and clean them with lukewarm water and non-abrasive detergent. Make sure to remove any encrustations. Dry them thoroughly and return them to the hob. Flame-spreader crowns and burner caps For easier cleaning, the flame-spreader crowns...

Installation 36 5 Installation 5.1 Safety instructions Veneers, adhesives or plastic coatings on adjacent furniture should be temperature-resistant ( >90°C ), otherwise they might warp over time. The minimum distances must also be respected for the edges of the hob on the back as indicated in the...

Installation 37 EN 5.3 Mounting Over built-in oven The distance between the hob and the kitchen furniture or other installed appliances must be enough to ensure sufficient ventilation and air discharge.If installed above an oven, a space must be left between the bottom of the hob and the top of the ...

Installation 38 Hob seal To prevent leakage of liquid between the frame of the hob and the work surface, place the adhesive seal provided along the entire outer edge of the hob before assembly. 5.4 Fixing brackets Screw the fixing brackets ( A ) into the holes on the sides of the bottom casing to pr...

Installation 39 EN Carefully screw the connector 3 to the gas connector 1 of the appliance, placing the seal 2 between them. Connection with a flexible steel hose with conical fitting Make the connection to the gas mains using a continuous wall flexible steel hose whose specifications comply with th...

Installation 40 Extraction of the combustion products The combustion products may be extracted by means of hoods connected to a natural draught chimney whose efficiency is certain or via forced extraction. An efficient extraction system requires precision planning by a specialist qualified in this a...

Installation 41 EN Removing the hob top 1. Remove the grids from the hob. 2. Remove the flame-spreader crowns and relative burner caps. 3. Pull the knobs upwards to remove them. 4. Unscrew the burner rings using the supplied wrench. 5. Remove the top.

Installation 42 Replacing nozzles 1. Unscrew screw A and push air regulator B as far as it will go. 2. Use a spanner to remove the nozzles C and install the new ones for the required gas supply, following the indications given in the relevant table (see “Gas types and Countries”). 3. Adjust the air ...

Installation 43 EN Adjusting the minimum setting for LPG Tighten the screw located at the side of the tap rod clockwise all the way. Lubricating the gas taps Over time the gas taps may become difficult to turn and get blocked. Clean them internally and replace the lubrication grease. Following adjus...

Installation 44 Gas types and Countries N o Gas types IT GB-IE FR-BE DE AT NL ES PT SE RU DK 1 Natural Gas G20 G20 20 mbar • • • • • • • • • G20/25 20/25 mbar • 2 Natural Gas G25 G25 25 mbar • 3 Natural Gas G25 G25 20 mbar • 4 LPG G30/31 G30/31 28/37 mbar • • • • G30/31 30/37 mbar • • G30/31 30/30 m...

Installation 45 EN Burner and nozzle characteristics tables Nozzles which are not provided are available at Authorised Service Centres. 1 Natural Gas G20 AUX SR RR R1 R2 Rated heating capacity (kW) 1.1 1.7 2.6 3.5 3.0 Nozzle diameter (1/100 mm) 76 95 117 135 126 Reduced capacity (W) 400 500 750 1050...

Installation 46 5.7 Electrical connection General information Check the grid characteristics against the data indicated on the plate.The identification plate bearing the technical data, serial number and brand name is visibly positioned on the appliance.Do not remove this plate for any reason.Perfor...