Sherwood AX-5103 - Manuals - manualsarea.com

Page 2 - READ THIS BEFORE OPERATING YOUR UNIT; FOR YOUR SAFETY; ENGLISH

3 READ THIS BEFORE OPERATING YOUR UNIT Units shipped to the U.S.A and Canada are designed foroperation on 120 Volts AC only. Observe all safety precaution for use of a polarized ACplug. However, some products may be supplied with anon polarized plug. CAUTION : To prevent electric shock, match wide b...

Page 3 - CONTENTS

Page 4 - System Connections

5 ENGLISH AC OUTLET 230V~50HzSWITCHED 100W(0.43A) MAX. AC INPUT 230V~50Hz 190W PHONO CD TUNER TAPE 1 /MD IN OUT IN OUT TAPE 2 MONITOR DIGI LINK SPEAKER A SPEAKER B AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.WARNING : SHOCK HAZARD-DO NOT OPEN.WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK...

Page 5 - CONNECTING SPEAKERS

6 AC OUTLET 230V~50HzSWITCHED 100W(0.43A) MAX. AC INPUT 230V~50Hz 190W PHONO CD TUNER TAPE 1 /MD IN OUT IN OUT TAPE 2 MONITOR DIGI LINK SPEAKER A SPEAKER B AVIS : RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR.WARNING : SHOCK HAZARD-DO NOT OPEN.WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT...

Page 6 - Front Panel Controls

⑧ BALANCE CONTROL KNOB Adjust the stereo balance between left and rightspeakers.• The center position is the normal condition. ⑨ TONE DIRECT SWITCH Press this switch to bypass the tone (bass and treble)circuitry for pure sound. ⑩ LOUDNESS SWITCH Press this switch to emphasize the sound of frequencie...

Page 7 - DIGI LINK III System Remote Controls

8 DIGI LINK III System Remote Controls • You can remotely control not only this amplifier but also Sherwood compatible components bearing the DIGI LINK II or III logo.• For system remote control operation, first make the DIGI LINK connections. • In the DIGI LINK III remote control system, if pressin...

Page 9 - Operations; LISTENING TO A PROGRAM SOURCE; Before operation; TAPE MONITOR function

Operations LISTENING TO A PROGRAM SOURCE 10 Before operation In the standby mode, turn the power on. 1 Select the desired input source. 3 Switch the desired speakers on. 2 • Enter the standby mode. • The STANDBY indicator lights up. This means that the amplifier is not disconnected fromthe AC mains ...

Page 11 - RECORDING; Recording with TAPE 1/MD

12 RECORDING Select the desired input as recordingsource except for TAPE 1/MD and TAPE 2MONITOR. 1 Select the desired input as recordingsource except for TAPE 2 MONITOR. 1 Start recording on the tape deck or the MDrecorder connected to TAPE 1/MD. 2 Set the TAPE 2 MONITOR button to on. 2 Start play o...

Page 12 - Troubleshooting Guide

13 Troubleshooting Guide If your unit should not perform as expected, consult the table below to see if the problem can be correctedbefore seeking help from your dealer or our service organization. PROBLEM POSSIBLE CAUSE REMEDY No power No sound No recording • The AC input cord is disconnected • Poo...

Page 13 - Specifications; GENERAL

14 Specifications • Power output, 8 Ω , THD 0.3 %, 40 Hz � 20 kHz | 2 X 100 W • Total harmonic distortion, 8 Ω , 100 W, 1 kHz | 0.03 % • Intermodulation distortion 60 Hz : 7 kHz = 4 : 1 SMPTE, 8 Ω , 100 W | 0.05 % • Input sensitivity, 47 k Ω PHONO (MM) | 3.0 mV CD, TUNER, TAPE | 200 mV • Phono input...