Samsung VR30T85513B - Manuals

P REP ARA TION • For information on Samsung’s environmental commitments and product regulatory obligations, e.g. REACH, visit our sustainability page available via www.samsung.com Clean Station • Do not modify the polarized plug to fit a non-polarized outlet or extension cord. • Do not use outdoors ...

P REP ARA TION Jet Bot • Do not pick up hard or sharp objects such as glass, nails, screws, coins, and etc. • Do not use without a filter in place. When servicing the unit, never put fingers or other objects into the fan chamber in case the unit accidentally turns on. • Do not put any objects into o...

P REP ARA TION Power related WARNING • Please prevent any risk of electric shock or fire. – Do not damage the power cord. – Do not pull the power cord too hard or touch the power plug with wet hands. – Do not use a power source other than rated volatge of the charger and also do not use a multi-outl...

P REP ARA TION • Be sure the Jet Bot does not suck in or touch any kind of liquids (water, beverage, filth, etc.). – The Jet Bot can be severely damaged and it may contaminate other areas if the wheels pass through liquid. • Do not spill any liquids on the Clean Station. – There is a risk of fire or...

P REP ARA TION In use WARNING • If any abnormal sounds, smells or smoke come from the Jet Bot, immediately shut off the power switch of the Jet Bot and contact a service center. CAUTION • Using the Jet Bot on a thick carpet may damage both the Jet Bot and the carpet. – The Jet Bot cannot pass over a...

P REP ARA TION Cleaning and maintenance WARNING • When the power cord is damaged, contact a service center to get it replaced by a certified repairman. – There is a risk of fire or electric shock. • Please check with a SAMSUNG Electronics service center when replacing batteries. – Using batteries fr...

INSTALLA TION INSTALLATION Installing a Clean Station Approximately 0.5 m Approximately 0.5 m Status Indicator Approximately 1 m 1 Connect the provided power cord to the bottom of the Clean Station. 2 Position the power cord into the fixing groove at the rear of the Clean Station. 3 Raise the front ...

OPERA TION Charging the Jet Bot Before using the Jet Bot for the first time, charge it completely. (For the charging time and cleaning time, refer to the ‘Product specification’.) 1 Open the upper cover of the Jet Bot and remove the white gasket. OFF ON 2 Remove the yellow gasket attached to the pow...

OPERA TION Status Indicator 4 Check the charging status. – When charging starts, the Status Indicator of the Jet Bot turns on (red, orange, or yellow depending on charging progress), it rises gradually, and changes to green when the charging is complete. Auto charging The Jet Bot automatically retur...

OPERA TION Checking if the docking (recharging) does not work Check the Clean Station’s installation status • Check whether the Clean Station has been installed in a place where the Clean Station cannot guide the Jet Bot to return. • Check whether the distance between the Clean Station and the Jet B...

OPERA TION Using the Jet Bot Before using the Jet Bot, press the power switch at the side of the Jet Bot to turn the Jet Bot on. ❇ ❇ For the normal use of the Jet Bot’s functions, the SmartThings connection is required. – For downloading and installing the SmartThings App, refer to the ‘SmartThings ...

OPERA TION Operation status on the LED Status Indicator Classification Color Meaning Jet Bot While operating Red Blinking without moving An error occurs. Blinking while moving Auto returning to the Clean Station due to low battery On Operating stops due to low battery While charging Red, orange, or ...

OPERA TION Cleaning Functions Cleaning Functions Operation Cleaning Methods • Auto Clean: Cleans automatically until the Jet Bot completes cleaning all rooms one time. • Room Clean: You can select a room you want to clean.• Spot Clean: You can set a specific area you want to clean. Cleaning Mode • Y...

OPERA TION Additional functions Additional functions Operation Energy-Saving Mode • When charging is complete, the Jet Bot automatically enters the Sleep Mode. While the Jet Bot is docked on the Clean Station, press and hold the [ ] for 7 seconds to set it to the Sleep Mode. To cancel the Sleep Mode...

OPERA TION Attaching Boundary Markers If Boundary Markers are attached before using the Jet Bot, the Jet Bot can operate safely. You can purchase additional Boundary Markers at a service center. To prevent the Jet Bot from entering the following areas, attach the Boundary Markers to the floor in a s...

OPERA TION Parts diagram Jet Bot 03 02 01 06 08 05 09 04 07 Top 01 Obstacle Sensor 02 Power switch 03 LiDAR Sensor 04 Dustbin 05 Start/stop button 06 Docking (Recharging) button 07 Status Indicator 08 Docking Sensor Window 09 Upper Cover 04 01 07 02 06 09 05 03 04 08 10 04 Bottom 01 Charging Pin 02 ...

MAINTENANCE Cleaning the Jet Bot Before maintenance work, you should turn off the power switch at the side of the Jet Bot. Emptying and cleaning the Dustbin 1 Grasp the Jet Bot’s cover at the groove and lift it up. 2 Hold the Dustbin handle and lift the Dustbin up. 3 Unlock the transparent clip at t...

MAINTENANCE Cleaning the brush 1 Push the Brush Cover Lock to the right to unlock. 2 Detach the brush cover. 3 Lift up the left side of the brush first and then pull the brush from the groove on the right. 4 Clean the brush. 5 Attach the brush. 6 Attach the brush cover. English 26 1_DJ68-00858H-04_I...

MAINTENANCE Cleaning the Sensor Window Wipe the Sensor Window with a soft cloth. Docking Sensor Window Obstacle Sensor Rear Sensor LiDAR Sensor Cliff Sensor Dust Sensor Cleaning the Driving Wheel 1 Place a soft cloth down first, turn the Jet Bot over, and place it gently on the cloth. 2 Remove forei...

MAINTENANCE Cleaning the Side Brush Cover the Side Brush with a hot steamed cloth for 10 seconds, then wipe the Side Brush. When the Side Brush is very tangled with hair, threads, etc., detach the Side Brush with a screwdriver while gripping the Side Brush, and remove the foreign matter. If the Side...

MAINTENANCE Cleaning the Clean Station Before cleaning the Clean Station, unplug the power cord from the electrical outlet. Replacing the Dust Bag 1 Press the [PUSH] button on the top of the Clean Station to open its cover. 2 Pull the top of the Dust Bag holder gently. – If you do not pull the Dust ...

MAINTENANCE Cleaning the bottom cover 1 Lay the Clean Station on its side and turn the 7 fixed screws on the bottom cover in the unlock direction( ). 2 Detach the cover and remove dirt. 3 Clean the cover with water and dry it completely in the shade. 4 Attach the cover to the Clean Station. 5 Turn t...

APPENDIX SmartThings App The SmartThings App is only compatible with models that have a Wi-Fi function.If you do not have a Wi-Fi router, you cannot use the SmartThings App. Setting up the wireless router • Please refer to the user manual of your wireless router for the settings of the wireless rout...

APPENDIX Downloading the SmartThings App • Download and install the SmartThings App from the markets (Google Play Store, Apple App Store, or SAMSUNG Galaxy Store). To find the app, use the keyword “SmartThings”. NOTE • SmartThings is incompatible with some tablets and some mobile devices.• Some iPad...

APPENDIX 4 [Android] The connection to your device will be progressed automatically. – [iOS] Open the setting app, and select [vacuum]_E30AJT** in the Wi-Fi list. 5 Provide the authentication when you are directed to do so. 6 [Android] The connection to your wireless router will be progressed automa...

APPENDIX Functions of the SmartThings App Classification Functions Explanation Monitoring Cleaning Report • You can check the result of the last cleaning.• You can check the histories of last 50 cleanings. Control Dock • You can stop cleaning and have the Jet Bot return to the Clean Station. Pause •...

APPENDIX Installation NOTE • Install the Clean Station in a place where the floor and wall are level.• If the cleaning area is wooden floors, it is best to install the Clean Station along the grain of wooden floors. • If the power switch is off, the Jet Bot will not charge even if it is docked on th...

APPENDIX Using NOTE • The Jet Bot may get caught on thresholds of entrance door or veranda, etc. during cleaning. – To restart operation, shut off the power switch, move the Jet Bot to an area where it can move easily, and then turn on the power again. • In a dark area, the Jet Bot may not recognize...

APPENDIX Battery usage NOTE • When you purchase a battery, check the SAMSUNG logo ( ) attached on the battery and the model name, then contact a service center. • This battery is exclusively for the SAMSUNG Electronics Jet Bot. Do not use it for any other products or purposes. • Do not disassemble o...

APPENDIX Corrective measures before reporting a problem 1 The Status Indicator turns red and blinks with a voice guide. 2 Turn off the power switch and check the instructions below and take appropriate actions. 3 When turning the Jet Bot on by pressing the power switch, the Status Indicator turns wh...

APPENDIX Troubleshooting Symptom Checklist The Jet Bot is not working at all. • Check if the power switch is on.• Check if the Status Indicator is on.• Check if the Jet Bot's battery is depleted. – When the Jet Bot’s Status Indicator turns red and stays red, place the Jet Bot manually on the Clean S...

APPENDIX Open Source Announcement The software included in this product contains open source software. To obtain the source code covered under licenses which have the obligation of publishing source code (e.g. GPL, LGPL… etc), please visit http://opensource.samsung.com/ and search by model name. It ...

APPENDIX Product Specification Classification Items VR30T85**** series Mechanical specifications Weight 3.4 kg Size W 350 mm x  D 350 mm x H 99.8 mm Cleaning method LiDAR location recognition Button method of the Jet Bot Touch type Electrical specifications Power consumption of the Jet Bot 60 W (Spo...