Ridgid R841150 - Manuals

6 The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and theexplanations with them, deserve your careful attention and understanding. The safety warnings do not by themselveseliminate any danger. The instructions or warnings they give are not substitu...

7 SPECIFICATIONS Chuck .............................................................................................................................................. 1/2 in. (13 mm) KeylessMotor ............................................................................................................

9 UNPACKING INSTRUCTIONS When unpacking the tool: ■ Carefully remove the tool and accessories from the box. ■ Make sure that all items listed in the packing list are in-cluded. ■ Inspect the tool carefully to make sure no breakage ordamage occurred during shipping. ■ Do not discard the packing mater...

10 WARNING: Do not allow familiarity with the hammer drill tomake you careless. Remember that a careless frac-tion of a second is sufficient to inflict severe injury. CHARGING BATTERY PACK The battery pack for this tool has been shipped in a lowcharge condition to prevent possible problems. Therefor...

11 30 min 30 min ? OPERATION LED BATTERY RED GREEN ACTION INDICATOR PACK LED LED Power Without battery pack ON OFF Ready to charge battery pack Evaluate Hot battery pack Flashing OFF When battery pack reachescooled temperature, chargerbegins fast charge mode Evaluate Cold battery pack Flashing OFF W...

12 Fig. 6 VARIABLE SPEED SWITCH TRIGGER OPERATION TO INSTALL BATTERY PACK ■ Lock the switch trigger on the drill by placing the directionof rotation (forward-reverse) selector in center position. See Figure 4. ■ Place battery pack in the drill. Align raised rib on batterypack with the groove inside ...

14 INSTALLING BITS See Figures 9 and 10. ■ Lock the switch trigger by placing the direction of rotationselector in center position. See Figure 4. ■ Open or close chuck jaws to a point where the openingis slightly larger than the bit size you intend to use. Also,raise the front of the drill slightly ...

16 OPERATION BIT STORAGE See Figure 14. When not in use, the bit provided with this drill can be placedin the storage area located on the rear of the drill. WARNING: Always wear eye protection marked to comply withANSI Z87.1. Failure to do so could result in dust,shavings, or loose particles being t...

17 TO ADJUST DRILLING OR HAMMER MODE See Figure 16. To adjust hammer drill to drilling or hammer operation, rotatemode selector in the direction of arrows as shown in Figure16. For your convenience a hammer symbol and drill bit sym-bol have been molded into the selector. WARNING: Your hammer drill h...

18 Fig. 18 Fig. 19 Fig. 17 MAINTENANCE WARNING: When servicing use only identical RIDGID ® replace- ment parts. Use of any other parts may create ahazard or cause product damage. GENERAL Avoid using solvents when cleaning plastic parts. Most plas-tics are susceptible to damage from various types of ...

19 R E C YCLE 1 .8 0 0 . 8 2 2 .88 37 R B R C N i C d ™ MAINTENANCE To obtain the longest possible battery life, we suggest thefollowing: ■ Store and charge your batteries in a cool area.Temperatures below 50°F or above 100°F will shortenbattery life. ■ Never store batteries in a discharged conditio...

20 This product is manufactured under license from Ridgid,Inc. by One World Technologies, Inc. All warrantycommunications should be directed to One WorldTechnologies, Inc. at (toll-free) 1-866-539-1710. 9 0 - D A Y S A T I S F A C T I O N G U A R A N T E EPOLICY During the first 90 days after the da...

® OPERATOR’S MANUAL 18 Volt1/2 in. (13 mm) Hammer DrillR841150Two Speed/Reversible Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information whenyou call or visit. For the location of the authorized service ...