Ridgid R84015 - Manuals - manualsarea.com

Page 3 - GENERAL SAFETY RULES; SAVE THESE INSTRUCTIONS

3 GENERAL SAFETY RULES WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result inelectric shock, fire and/or serious personal injury. SAVE THESE INSTRUCTIONS WORK AREA ■ Keep your work area clean and well lit . Cluttered benches and dark areas invit...

Page 4 - Always wear safety glasses with side shields.; IMPORTANT RULES FOR BATTERY TOOLS; Do not charge battery tool in a damp or wet location.

4 SERVICE ■ Tool service must be performed only by qualifiedrepair personnel. Service or maintenance performed by unqualified personnel may result in a risk of injury. ■ When servicing a tool, use only identical replace-ment parts. Follow instructions in the Maintenancesection of this manual. Use of...

Page 5 - IMPORTANT SAFETY INSTRUCTIONS FOR CHARGER

5 WARNING: Read and understand all instructions. Failure to follow all instructions listed below, may result inelectric shock, fire and/or serious personal injury. ■ Never use a battery that has been dropped orreceived a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dr...

Page 6 - Symbol; SYMBOLS

6 SAVE THESE INSTRUCTIONS The purpose of safety symbols is to attract your attention to possible dangers. The safety symbols, and theexplanations with them, deserve your careful attention and understanding. The safety warnings do not by themselveseliminate any danger. The instructions or warnings th...

Page 7 - INSTRUCTIONS; APPLICATIONS

7 Chuck ............................................................................................................................................... 1/2 in. (13 mm) Keyless Motor .........................................................................................................................

Page 8 - FEATURES; OFF

8 FEATURES Before using this tool, familiarize yourself with all operatingfeatures and safety requirements. However, do not letfamiliarity with the tool make you careless. WARNING: Exercise caution when using this tool. Careless ac-tions, for even a fraction of a second, can result inserious persona...

Page 10 - OPERATION; CHARGING BATTERY PACK; Do not; The battery pack for this; both; KEEPING THE VENTS CLEAN

10 OPERATION Fig. 2 WARNING: Do not allow familiarity with the tool to make youcareless. Remember that a careless fraction of asecond is sufficient to inflict severe injury. CHARGING BATTERY PACK The battery pack for this tool has been shipped in a lowcharge condition to prevent possible problems. T...

Page 11 - LED FUNCTION OF CHARGER

11 Evaluate Ev alu er Eva lua r Charging C ar ga nd o E n c ha rg e Fu ll Co m pl et o Ch ar ge m ax . Po we r Corriente Alimentation 30 min 30 min ? OPERATION LED BATTERY RED GREEN ACTION INDICATOR PACK LED LED Power Without battery pack ON OFF Ready to charge battery pack Evaluate Hot battery pack...

Page 12 - TO INSTALL BATTERY PACK; Remove the battery pack from your drill.; SWITCH; To turn your drill; ON; VARIABLE SPEED; You might hear a whistling or ringing noise from the; SELECTOR

12 OPERATION TO INSTALL BATTERY PACK ■ Lock the switch trigger on the drill by placing the directionof rotation (forward-reverse) selector in center position. See Figure 4. ■ Place battery pack in the drill. Align raised rib on batterypack with the groove inside the drill. See Figure 5. ■ Make sure ...

Page 13 - SPEED

13 REVERSIBLE See Figure 4. This tool has the feature of being reversible. The directionof rotation is controlled by a selector located above the switchtrigger. With the drill held in normal operating position, thedirection of rotation selector should be positioned to the leftof the switch for drill...

Page 14 - INSTALLING BITS; LOCK; REMOVING BITS; UNLOCK

14 INSTALLING BITS See Figure 9. ■ Lock the switch trigger by placing the direction of rotationselector in center position. See Figure 4. ■ Open or close chuck jaws to a point where the openingis slightly larger than the bit size you intend to use. Also,raise the front of the drill slightly to keep ...

Page 15 - ADJUSTABLE TORQUE CLUTCH; Rotate adjusting ring to the desired setting.; BIT STORAGE

15 OPERATION ADJUSTABLE TORQUE CLUTCH This drill is equipped with an adjustable torque clutch fordriving different types of screws into different materials.The proper setting depends on the type of material and thesize of screw you are using. TO ADJUST TORQUE ■ Identify the twenty four torque indica...

Page 16 - DRILLING

16 DRILLING See Figure 13. When drilling hard smooth surfaces use a center punch tomark desired hole location. This will prevent the drill bit fromslipping off center as the hole is started. However, the lowspeed feature allows starting holes without center punch-ing if desired. To accomplish this, ...

Page 18 - MAINTENANCE; When servicing use only identical RIDGID; General; disassemble battery pack

18 MAINTENANCE WARNING: When servicing use only identical RIDGID ® replace- ment parts. Use of any other parts may create ahazard or cause product damage. Do not abuse power tools. Abusive practices can damagetool as well as workpiece. WARNING: Do not at any time let brake fluids, gasoline, petro-le...

Page 19 - WARRANTY

19 This product is manufactured under license from Ridgid, Inc.by One World Technologies, Inc. All warranty communicationsshould be directed to One World Technologies, Inc. at (toll-free) 1-866-539-1710. 90-DAY SATISFACTION GUARANTEE POLICY During the first 90 days after the date of purchase, if you...

Page 20 - OPERATOR’S MANUAL; Customer Service Information:

20 ® OPERATOR’S MANUAL 18 Volt 1/2 in. (13 mm) Drill-DriverR84015Two Speed/Reversible Customer Service Information: For parts or service, contact your nearest RIDGID authorized service center. Be sure to provide all relevant information whenyou call or visit. For the location of the authorized servi...