Quadra-Fire QVI-25FB-S - Manuals

Page 2 - Congratulations; Listing Label Information/Location; Owner’s Manual; Read this manual before installing or operating this appliance.; Homeowner Reference Information; N A

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 2 Congratulations Listing Label Information/Location Model Name: ___________________________________________ Date purchased/installed: __________________ Serial Number: __________________________________________ Location on appliance: _______________...

Page 3 - Table of Contents

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 3 Table of Contents 1 Listing and Code Approvals A. Appliance Certifi cation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4B. BTU Specifi cations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4C. High Altitude Installations...

Page 4 - Note; Listing and Code Approvals; C. High Altitude Installations; Models; A. Appliance Certifi cation; Material which will not ignite and burn. Such materials are; E. Combustible Materials Specifi cation; WARNING; NOT INTENDED FOR USE AS A PRIMARY HEAT SOURCE.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 4 Note : To assure top performance, safety and effi ciency, inserts must be installed with an approved fl ue liner as per CAN/CGA B-149 or National Fuel Gas Code ANSI Z223 and these instructions. Note: This installation must conform with local codes....

Page 5 - Getting Started; C. Inspect Appliance and Components; • Read all of the instructions before starting the insta-; CAUTION; Any such action may cause a fi re hazard.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 5 Quadra-Fire gas inserts are designed for recessed installa-tions into solid fuel masonry or factory built non-combustible fi replaces that have been installed in accordance with the National, Provincial, State and local building codes. Prior to ins...

Page 6 - Fireplace Size Requirements; A. Minimum Fireplace Opening; • Any smoke shelves, shields, baffl es and the metal fl oor; NOTE: For actual appliance dimensions refer to Section 15.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 6 3 3 Fireplace Size Requirements A. Minimum Fireplace Opening Minimum fi replace opening requirements are shown in Figure 3.1. • The fi rebrick (refractory), glass doors, screen rails, screen mesh and log grates can be removed from a factory built f...

Page 8 - A. Vent Termination Minimum Clearances; Termination Locations

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 8 Fire Risk. Asphyxiation Risk. • Terminations MUST meet minimum clearances. • Exhaust gases are hot. • Nearby vents may draw fumes into house. A. Vent Termination Minimum Clearances Figure 4.1 specifi es minimum vent heights for various pitched roof...

Page 9 - C. Measuring Standards; • Vertical terminations are measured to top of chimney.; B. Horizontal Venting; Horizontal venting is NOT allowed.; Vent Information and Diagrams; Symbol

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 9 CAUTION ALL vent specifi cations MUST be followed. • This product is tested and listed to these specifi cations. • Appliance performance will suffer if specifi cations are not followed. Figure 5.1 C. Measuring Standards Vertical measurements listed...

Page 10 - Installation Preparation; D. Hearth or Hearth Extension

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 10 6 6 Installation Preparation Fire Risk. A hearth or hearth extension (if present) must comply with either of the following: • The solid fuel burning fi replace manufacturer’s specifi cation. • Local building codes required by authority having juri...

Page 11 - A. Venting Components; Installing Vent Pipe and Appliance; B. Connecting Vent Pipe

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 11 A. Venting Components 7 7 Installing Vent Pipe and Appliance The vertical vent termination system installed on this model includes: • One 3-foot section stainless steel fl exible pipe (included with insert). • One length of 3-inch fl exible vent p...

Page 14 - D. Installing Adaptor and Termination Cap; Damper Flashing Kit; : Damper may have to be removed to use this kit.; system REQUIRES this insulation.; Masonry; OR

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 14 D. Installing Adaptor and Termination Cap For installation of termination cap see minimum vent heights for various pitched roofs (see Figure 7.2) . To install adaptor see Figure 7.3. Roof Pitch H (Min.) Ft.Flat to 6/12....................1.0*Over ...

Page 15 - Gas Information; • If substituting for these components, please consult; Pressure

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 15 • Ensure that gas line does not come in contact with outer wrap of appliance. Follow local codes. • Incoming gas line should be piped into the valve compartment and connected to the 1/2 inch connection on the manual shutoff valve. • Check all fi t...

Page 16 - HIGH ALTITUDE INSTALLATIONS; • A small amount of air will be in the gas supply lines.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 16 Fire hazard. Do NOT change the valve settings. • This valve has been preset at the factory. • Changing valve settings may result in fi re hazard or bodily injury. HIGH ALTITUDE INSTALLATIONS U.L. Listed gas appliances are tested and approved witho...

Page 17 - A. Wiring the Appliance; Electrical Information; • An ON/OFF switch is included with the decorative; Appliance Requirements; • This appliance DOES NOT require 110-120 VAC to

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 17 A. Wiring the Appliance 9 9 Electrical Information Note : This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canad...

Page 18 - B. Junction Box Installation; Optional Accessories

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 18 B. Junction Box Installation Figure 9.2 Junction box installation FEED PLUG THROUGH HOLE INSERT RELIEF AROUND CORD IN THIS END FROM OUTSIDE OF UNIT JUNCTION BOX SIDE WALL Optional Accessories Connecting the electrical junction box is required if u...

Page 20 - A. Mantel Projections; Finishing

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 20 A. Mantel Projections Figure 10.1 shows the minimum vertical and corresponding maximum horizontal dimensions of appliance mantels or other combustible projections above the top front edge of the appliance, not the surround. 10 10 Finishing Figure ...

Page 21 - Appliance Setup; A. Remove Shipping Materials; Placing the Ember Material; • Embers CANNOT be placed directly over ports.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 21 Figure 11.1 Placement of Embers BURNER PAN EMBER PLACEMENT 11 11 Appliance Setup A. Remove Shipping Materials Remove shipping materials from inside or underneath the fi rebox. B. Clean the Appliance Clean/vacuum any sawdust that may have accumulat...

Page 22 - LOG PLACEMENT; Log Placement; Logs are fragile! Carefully remove the logs from; FIREBOX LEDGE

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 22 E. Positioning the Logs Log Set Assembly: LOGS-2031 2031-700 4 5 6 1 3 2 FIREBOX LEDGE LOG PLACEMENT INSTRUCTIONS Log Placement CAUTION: Logs are fragile! Carefully remove the logs from the packaging. LOG #1 FIREBOX LEDGE FIREBOX FIREBOX LEDGE LOG...

Page 23 - of log contacts log tab near the center of the burner.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 23 LOG #3 (SRV2032-703): Position log #3 by locating its slot over the tab on right front of the burner such that left end of log contacts log tab near the center of the burner. LOG #2 (SRV2032-702): Position log #2 by locating its slot over the tabs...

Page 24 - Assembly; Removing Glass Assembly; • To release glass assembly, pull latch forward and allow; Replacing Glass Assembly; G. Air Shutter Setting; NG; Burner

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 24 Figure 11.2 Glass Assembly F. Glass Assembly Removing Glass Assembly There are two glass latches on the left side of glass as-sembly and two glass latches on the right side. • To release glass assembly, pull latch forward and allow to retract away...

Page 25 - A. Before Lighting Appliance; Operating Instructions; HOT SURFACES

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 25 Fire Risk. Explosion Risk. Gas may build up while lighting pilot. • Remove glass assembly before lighting pilot. • Replace glass assembly after lighting pilot. A. Before Lighting Appliance This appliance has a Standing Pilot Ignition. Before opera...

Page 26 - B. Lighting Appliance; Standing Pilot Ignition; NOT FOR USE; WHAT TO DO IF YOU SMELL GAS

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 26 B. Lighting Appliance Standing Pilot Ignition 1. Turn off all electric power to the appliance if service is to be performed. 2. Open control access panel. 3. Move switch to “OFF” position. 4. Push in gas control knob slightly and turn clock- wise ...

Page 27 - Initial Break-in Procedure

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 27 C. Check Pilot Flame Appearance Pilot fl ame must contact the thermocouple and thermopile for reliable appliance operation. • Pilot fl ame should be as shown in Figure 12.1. D. After Appliance is Lit Initial Break-in Procedure When you light the a...

Page 28 - E. Frequently Asked Questions; ISSUE

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 28 E. Frequently Asked Questions Fire Risk. High Temperatures. Keep combustible household items away from appliance. Do NOT obstruct combustion and ventilation air. • Do NOT place combustible items on top of or in front of appliance. • Keep furniture...

Page 29 - A. Standing Pilot Ignition System; Troubleshooting; Symptom

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 29 A. Standing Pilot Ignition System 13 13 Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qu...

Page 31 - When cleaning glass door:

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 31 14 14 Maintaining and Servicing Appliance Although the frequency of appliance servicing and maintenance will depend on use and the type of installation, a qualifi ed service technician should perform an appliance checkup at the beginning of each h...

Page 33 - Reference Materials; A. Appliance Dimension Diagram; Location

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 33 Figure 15.1 Appliance Dimensions A 14-7/16 in. 377 mm C E 5-9/16 in. 1-1/16 in. G GAS INLET (GAS BALL VALVE NOT SHOWN) H F D 3-5/8 in. REF 92 mm 3-7/16 in. 87 mm 1-1/16 in. 27 mm Two 2-13/16 in. 71 mm B 4-3/8 in.111 mm 1-9/16 in. 40 mm 15 15 Refer...

Page 34 - B. Vent Kits Components; Direct Vent Flex Liner Accessory Kits

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 34 B. Vent Kits Components Direct Vent Flex Liner Kits (see Figure 15.2) LINK-DV-30B or (LINK-DV-30): Masonry 3 inch fl ex liner kit. Expands to 30 feet. Includes: two liners, termination cap, fl ashing, and link adapter. LINK-DV4-30B or (LINK-DV4-30...

Page 35 - Service Parts Diagram; C. Service Parts List; Part number list on following page.; Log Set Assembly

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 35 Service Parts Diagram QVI-25FB-S R Beginning Manufacturing Date: Oct. 2007 Ending Manufacturing Date: ______ C. Service Parts List Part number list on following page. Log Set Assembly 4 2 1 3 5 6 7 8 9 10 11 12 13 14 15 16

Page 36 - ITEM

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 36 QVI-25FB-S Service Parts IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer....

Page 37 - Valve Assembly Parts List; Service Parts; Valve Assembly

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 37 IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. Stocked at Depot ITEM DE...

Page 38 - D. Limited Lifetime Warranty; LIMITED LIFETIME WARRANTY; Lifetime Warranty

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 38 D. Limited Lifetime Warranty LIMITED LIFETIME WARRANTY The Hearth & Home Technologies limited Lifetime Warranty guarantees that the following components will work as designed for the lifetime of the stove or Hearth & Home Technologies will...

Page 39 - E. Contact Information; For the location of your nearest Quadra-Fire dealer,; DO NOT DISCARD THIS MANUAL

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. D • 3/08 39 Quadra-Fire, a brand of Hearth & Home Technologies Inc. 20802 Kensington Boulevard, Lakeville, MN 55044 www.quadrafi re.com E. Contact Information Please contact your Quadra-Fire dealer with any questions or concerns. For the location of your ...