Planar PL1700M - Manuals - manualsarea.com

Page 3 - Contents; Preface

1 Contents Preface ......................................................................................................................... 2 Installation ................................................................................................................. 4 Unpacking .....................

Page 4 - Warning

2 Preface This manual is designed to assist users in setting up and using the LCD Monitor. Information in this document has been carefully checked for accuracy; however, no guarantee is given to the correctness of the contents. The information in this document is subject to change without notice. Th...

Page 6 - Installation; Unpacking

4 Installation Unpacking Before unpacking the LCD Monitor, prepare a suitable workspace for your Monitor and computer. You need a stable and clean surface near a wall power outlet. Make sure that the LCD Monitor has enough space around it for sufficient airflow. Though the LCD Monitor uses very litt...

Page 7 - Interface for Arm Applications

5 Connecting the LCD Monitor and Base W h e n y o u o p e n t h e b o x , t a k e t h e b a s e a n d p u t o n t h e d e s k f i r s t . T h e n c o n n e c t t h e L C D M o n i t o r a n d b a s e . ( S e e f i g . 1 - 1 ) Figure 1-1 Viewing Angle Adjustment T h e L C D M o n i t o r i s d e s i ...

Page 8 - Connecting the AC Power; Connecting the Audio Cable; Power Management System

6 Connecting the AC Power 1. Connect the power cord to the LCD Monitor.(See Fig. 1-6) 2. Connect the power cord to an AC power source. Connecting the Audio Cable 1. Connect the audio cable to the “LINE OUT “ jack on your PC's audio card or to the front panel's “AUDIO OUT” jack of your CD ROM drive. ...

Page 9 - Display Controls; User Controls; Attention

7 Display Controls User Controls A brief description and the location of all LCD Monitor functions controls and indicators: Figure 2-1 1 Power LED will be Green when the monitor is on, Yellow when in power saving mode, and Dark when the monitor is off. Press this button to turn on and turn off the m...

Page 10 - Function Description; User

8 Function Description Icon Function Function Description Brightness 101 scales of brightness are available to choose from (0 to 100). Contrast 101 scales of contrast are available to choose from (0 to 100). H. Position This function let's you adjust the display's horizontal position. V. Position Th...

Page 11 - OSD Lock Out Function

9 OSD Lock Out Function When monitor is in normal display, you can enable the “OSD Lock Out” function. Option 1: OSD lock – all 4 buttons are locked except the “POWER” button. Press and hold the , and buttons for same time 3 seconds to lock the buttons. The monitor will show an “OSD Lock Out” messag...

Page 12 - Technical Information; Specifications

10 Technical Information Specifications LCD Panel Size 17" (43 cm) Display Type Active matrix color TFT LCD Resolution 1280 x 1024 Display Dot 1280 x (RGB) x 1024 Display Area (mm) 337.92 x 270.336 (H x V) Display Color 16.2M (RGB 6 bit+FRC) Lamp Voltage (typical) 650 Vrms Lamp Current (typical)...

Page 13 - Size and Weight

11 Power Management Mode Power Consumption* AC Input LED Color DPM ON 48W maximum 240 VAC GREEN DPM OFF 2W maximum 240 VAC Yellow DC switch off 1W maximum 240 VAC Dark Disconnected 2W maximum 240 VAC Dark Meeting VESA DPM requirements measured from AC Input end of AC power cord. Sync Input Analogue ...

Page 14 - Standard Timing Table

12 Standard Timing Table If the selected timing is NOT included in table below, this LCD monitor will use the most suitable available timing. SYNC TOTAL ACTIVE SYNC FRONT BACK PIXEL TIMING FH(kHZ) FV(HZ) POLARITY (DOT/ LINE) (DOT/ LINE) WIDTH (DOT/LINE) PORCH (DOT/LINE) PORCH (DOT/LINE) FOREQ (MHZ) ...

Page 16 - Troubleshooting

14 Troubleshooting This LCD Monitor has pre-adjusted using factory standard VGA timings. Due to the output timing differences among various VGA cards in the market, users may initially experience an unstable or unclear display whenever a new display mode or new VGA card is selected. Attention This L...