Pelco WLV2500 - Manuals - manualsarea.com

Page 2 - ii; TABLE OF CONTENTS; INTERCEPT

ii Pelco Manual C914M (7/96) ®Pelco and the Pelco logo are registered trademarks of Pelco.©Copyright 1996, Pelco. All rights reserved. TABLE OF CONTENTS Section Page 1.0 WARNINGS ............................................................................................................................

Page 4 - iv

(This page intentionally left blank.) iv Pelco Manual C914M (7/96)

Page 5 - literature accompanying this unit.; RISK OF ELECTRIC SHOCK.; prior to installation and operation.; The product may bear the following marks:; CAUTION

Pelco Manual C914M (7/96) 1 This symbol indicates that there are importantoperating and maintenance instructions in the literature accompanying this unit. CAUTION: RISK OF ELECTRIC SHOCK. DO NOT OPEN. Please thoroughly familiarize yourself with the information in this manual prior to installation an...

Page 7 - Transmitter-Receiver Placement at Same Site; ANTENNA LOCATION; - Move the antennas to different locations.

Pelco Manual C914M (7/96) 3 Figure 2. Transmitter-Receiver Placement at Same Site 4.0 ANTENNA LOCATION To provide the best reception, proper placement of thetransmit and receive antennas is important. Receptionwill be best when: • The antennas are a minimum of 8-10 feet abovethe floor (indoors) or g...

Page 8 - Proper placement of the; ENCLOSURE MOUNTING; If you mount the WLV2000 receiver

4 Pelco Manual C914M (7/96) 5.0 INSTALLATION NOTE: Proper placement of the transmit and receive antennas isimportant for best reception.Read Section 4.0, “Antenna Lo-cation,” before installing theequipment. Install the WLV500 receiver and WLV2000 transmit-ter at the remote site where your camera wil...

Page 10 - ANTENNA ALIGNMENT; This section applies only to the

6 Pelco Manual C914M (7/96) 5.4 ANTENNA ALIGNMENT NOTE: This section applies only to the WLV2000 wireless receiver. 1. Connect a high impedance voltmeter to the RSSI(Received Signal Strength Indication) test pointson the bottom of the enclosure: a. Set the voltmeter on a low-volt DC scale (3 or10 vo...

Page 11 - Feet; Do not service the

Pelco Manual C914M (7/96) 7 4. Check the power supply voltages for the wirelesstransmitter and receiver. If the voltage at the trans-mitter or receiver is less than 11 VDC, replace theunit’s power supply. 5.5.2 Poor Picture 1. Refer to Section 4.0, “Antenna Location,” andverify that the transmit and...

Page 12 - Outdoor Enclosure Exploded Assembly Diagram

8 Pelco Manual C914M (7/96) 6.0 EXPLODED ASSEMBLY DIAGRAM (OUTDOOR MODELS ONLY) Figure 6. Outdoor Enclosure Exploded Assembly Diagram

Page 13 - MECHANICAL PARTS LIST

Pelco Manual C914M (7/96) 9 6.1 MECHANICAL PARTS LIST Item Quantity Description Part Number 1 1 9-Pin Connector CON03-06-1091 2 2 Gland EH400010003 3 2 Gland Nut EH400010004 4 1 Gland CX950010000 5 1 Gland Nut CX950010001 6 2 Fuse Holder FUS342012L 7 1 Power Supply Assembly PCB9000281ASSY 8 1 3-Posi...

Page 14 - DOME MODIFICATION; d o m e d r i v e s D D 0 8 C X X , D D 0 8 E X X ,; receiver backplane and remove the; NOTE; : This step has changed Plug 13 on the

10 Pelco Manual C914M (7/96) 7.0 INTERCEPT ® DOME MODIFICATION To use the WLV500 wireless control system with In-t e r c e p t ® d o m e d r i v e s D D 0 8 C X X , D D 0 8 E X X , DD14CXX, or DD14EXX (domes with 360 degree ro-tation), the following steps must be performed: NOTE : Refer to Figure 7,...

Page 17 - ELECTRICAL; NRZ

Pelco Manual C914M (7/96) 13 8.0 WIRING DIAGRAM NOTE: Output voltage is 15 VDC, not 10.5 Figure 11. Outdoor Enclosure Wiring Diagram 9.0 MAINTENANCE In cold, wet areas periodically visit the transmitter andreceiver sites to prevent the buildup of snow and ice onthe enclosures. A buildup of ice and s...

Page 19 - WARRANTY; RETURNS

Pelco Manual C914M (7/96) 15 11.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtrademarks of Pelco.Endura and ExSite are trademarks of Pelco. © Copyright 1996, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, wit...

Page 20 - Pelco

Pelco 3500 Pelco Way, Clovis, CA 93612-5699 (559) 292-1981 • (800) 289-9100 FAX (800) 289-9150 or (559) 292-3827 International customers call 1-559-292-1981 or FAX 1-559-348-1120 (Product specifications subject to change without notice.) C914M