Pelco WD57 - Manuals - manualsarea.com

Page 2 - REVISION HISTORY; Revised defroster kit installation instructions.; CONTENTS; LIST OF ILLUSTRATIONS

2 Pelco Manual C1423M-D (10/03) REVISION HISTORY Manual # Date Comments C1423M 6/95 Original manual. C1423M-A 4/96 Rev. A. Incorporated Manual C1424M for blower kits.Incorporated Manual C1425M for defroster kits. Addedinstructions for installation of O/I-PCB circuit board kit.Added Operation and Car...

Page 3 - Only use replacement parts recommended by Pelco.; The product and/or manual may bear the following marks:; RISK OF

Pelco Manual C1423M-D (10/03) 3 Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.0 GENERAL 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation a...

Page 4 - Circuit board with thermostats; Agency Complance Certification

4 Pelco Manual C1423M-D (10/03) 2.0 DESCRIPTION The information in this manual covers the installation and operation of the followingkits for the EH5700/EHS700L Series environmental enclosures: BK57-1 Blower kit, 120 VAC, 15 watts BK57-2 Blower kit, 24 VAC, 10 watts BK57-3 Blower kit, 230 VAC, 15 wa...

Page 5 - BLOWER KIT INSTALLATION; Continuous Duty Operation Only -; If you are using your enclo-

Pelco Manual C1423M-D (10/03) 5 3.0 BLOWER KIT INSTALLATION This section provides instructions for installing the BK57-1. BK57-2. and BK57-3blower kits. For the following instructions, refer to Figure 1. Table B lists the parts shown in Figure 1. 1. Turn off power to the enclosure. 2. Unlatch and ra...

Page 6 - Wire Gauge; Maximum distance from transformer to load; 4 VAC Wiring Distances; otal vA; An enclosure that re-

6 Pelco Manual C1423M-D (10/03) Wire Gauge Maximum distance from transformer to load Table A. 24 VAC Wiring Distances The following are the recommended maximum distances for 24 VAC applicationsand are calculated with a 10-percent voltage drop. (Ten percent is generally themaximum allowable voltage d...

Page 8 - Exploded Assembly Parts List for Blower; Item; Exploded Assembly Diagram for Blower

8 Pelco Manual C1423M-D (10/03) Table B. Exploded Assembly Parts List for Blower Item Qty Description Part Number 1 1 Vent Grill, Beige 57004105COMP 1 Vent Grill, Gray 57004005COMP 2 2 Foam Filter EH550010045 3 1 24 VDC Fan Rectifier (for -2 model only) PCB9000277ASSY 4-7 Not Used 8 1 Fan Wire Cord ...

Page 9 - HEATER KIT INSTALLATION; O/l PCB Not Installed

Pelco Manual C1423M-D (10/03) 9 4.0 HEATER KIT INSTALLATION This section provides instructions for installing the HK57-1, HK57-2, and HK57-3heater kits. For the following instructions, refer to Figure 2. Table C lists the pans shown inFigure 2. 1. Turn off power to the enclosure. 2. Unlatch and rais...

Page 10 - Connector; Exploded Assembly Parts List for Heaters

10 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 1 1 Bracket/Heat sink 57004020COMP 2 2 Heater, 230 VAC HTR40220 2 Heater, 24 VAC HTR20024 2 Heater, 120 VAC HTR50120 3 1 Connector CON1-480424-0 A 2 Spacer, .500" Length SPA8423 B 4 Internal Tooth Lock Washer, #4 ZH4LWSIS C 4 Scre...

Page 11 - DEFROSTER KIT INSTALLATION; Window defrosters manufac-

Pelco Manual C1423M-D (10/03) 11 5.0 DEFROSTER KIT INSTALLATION This section provides instructions for installing the WD57-1, WD57-2, and WD57-3defroster kits. For the following instructions, refer to Figure 3. Table D lists the parts shown inFigure 3. 1. Turn off power to the enclosure. 2. Unlatch ...

Page 12 - Window Defroster, 120 VAC; Exploded Assembly Parts List for Defroster

12 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 1 1 Window Defroster, 120 VAC 570010003 1 Window Defroster, 24 VAC 570010006 1 Window Defroster, 230 VAC 570010005 2 1 Connector Plug CON1-480318-0 Table D. Exploded Assembly Parts List for Defroster Figure 3. Exploded Assembly Diagra...

Page 13 - CIRCUIT BOARD KIT INSTALLATION; Reinstall the camera and sled.

Pelco Manual C1423M-D (10/03) 13 6.0 CIRCUIT BOARD KIT INSTALLATION This section provides instructions for installing the O/I-PCB circuit board kit. For the following instructions, refer to Figure 4. Table E lists the parts shown inFigure 4. 1. Install the circuit board kit (O/I-PCB): a. Remove the ...

Page 14 - Exploded Assembly Parts List for Circuit Board

14 Pelco Manual C1423M-D (10/03) Item Qty Description Part Number 1 Not Used 2 Not Used 3 Not Used 4 1 Power Supply Barrier Cover EH470010019 5 2 Power Supply Barrier EH47004029COMP 6 1 Circuit Board PCB9000276ASSY 7 1 Circuit Board Insulator EH450010256 A Not Used B 2 Internal Tooth Lock Washer, #4...

Page 16 - Input Wiring Diagram

16 Pelco Manual C1423M-D (10/03) Figure 5. Input Wiring Diagram 00967

Page 17 - C) and to turn them off; CARE AND MAINTENANCE; Remove the vent grill and take out the filters.

Pelco Manual C1423M-D (10/03) 17 7.0 OPERATION If your enclosure has a thermostatically controlled blower, the thermostat is set toturn the fan on between 77 ° and 93 ° F (25 ° and 34 ° C) and to turn the fan off be- tween 62 ° and 78 ° F (17 ° and 26 ° C) If your enclosure has thermostatically cont...

Page 20 - WARRANTY AND RETURN INFORMATION; WARRANTY; RETURNS

20 Pelco Manual C1423M-D (10/03) 9.0 WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit,Genex, Legacy, and Spectra are registeredtrademarks of Pelco.Endura and ExSite are trademarks of Pelco. © Copyright 2003, Pelco. All rights reserved. WARRANTY Pelco will repair or replace, ...