Pelco VA6200 - Manuals - manualsarea.com

Page 2 - LIST OF ILLUSTRATIONS; CONTENTS; LIST OF TABLES

2 C841M-A (7/02) LIST OF ILLUSTRATIONS Figure Page 1 Jumper Settings - VA6200 Series .................................................................................................................................................................... 4 2 Fixed Cameras with Terminated Inputs ............

Page 3 - IMPORTANT SAFEGUARDS AND WARNINGS; Use only replacement parts recommended by Pelco.; DESCRIPTION; controller. The switchers have an; MODELS

C841M-A (7/02) 3 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should be observed. 1. Installation and servicing should be done only by qualified service personnel and conform to all local codes. 2. Unless the unit is specifically marked as a...

Page 4 - INSTALLATION; Remove the cover from the switcher.

4 C841M-A (7/02) INSTALLATION 1. Remove the cover from the switcher. 2. Set the jumpers as required for your application. Refer to Figure 1 and Table A. 3. Replace the cover. 4. Place the unit on a flat surface or install it in an equipment rack using the appropriate rack-mount kit. 5. Make all equi...

Page 5 - Jumper Settings - VA6200 Series; Jumper; Video Coaxial Cable Requirements; Maximum Distance

C841M-A (7/02) 5 Table A. Jumper Settings - VA6200 Series Jumper Position Function JP1 - JP20 A Camera input terminated (75 ohms) B Camera input looping (high impedance) JP23, JP24, JP25, JP26, JP28, JP31 A Camera titles on Monitor 1 B Camera titles on Monitor 2 JP29 or JP32 A PAL video standard B N...

Page 8 - Connector Assembly

Page 9 - OPERATION; SEQUENCING; VIEWING THE STATUS OF CAMERAS IN A SEQUENCE; Camera Status

C841M-A (7/02) 9 OPERATION To operate the VA6200 Series Switcher: 1. Plug in the power cord. 2. Select the monitor by pushing the MON 1 or MON 2 button. 3. Press a camera button to view video from the corresponding camera. SEQUENCING To run a sequence: 1. Select a monitor by pushing the MON 1 or MON...

Page 11 - ALARMS; To enable or disable alarms:; EXTERNAL TRIGGER; Operate the unit in the desired default setting.

C841M-A (7/02) 11 ALARMS The alarm inputs must be enabled or disabled if you connected alarms on the switcher to them. To enable or disable alarms: 1. Press the MON 1 button. 2. Press the recessed ALARM switch. The switch toggles the alarm inputs on and off. When the ON LED is lit, the alarminputs a...

Page 12 - TROUBLESHOOTING; PROBLEM; Fuse Table

12 C841M-A (7/02) TROUBLESHOOTING PROBLEM SOLUTION No power Check the fuse . Video output quality poor Check jumper settings (Refer to Figure 1, Table A). (Examples: Squiggly video, poor contrast, picture not centered) Locked system or sequencing not working as desired Reset the switcher. There are ...

Page 13 - SPECIFICATIONS; VIDEO

C841M-A (7/02) 13 SPECIFICATIONS VIDEO Inputs: Terminating (75 ohms) or looping (high impedance) NTSC and PAL compatible Outputs Monitor 1: 75 ohms Monitor 2: 75 ohms; half duplex (Coaxitron ® compatible). Requires field jumper change Gain: Unity Dwell: Camera dwell independently adjustable from 1 t...

Page 14 - GENERAL; Construction

14 C841M-A (7/02) GENERAL Construction Chassis: Steel, zinc plated Cover: Steel, textured black enamel Panel: Aluminum, with LEXAN ® overlay Dimensions VA6204 Series: 1.75 (H) x 5.50 (W) x 9.25 (D) inches (4.44 x 13.97 x 23.49 cm)VA6208 Series: 1.75 (H) x 8.75 (W) x 11.75 (D) inches (4.44 x 22.23 x ...

Page 15 - PRODUCT WARRANTY AND RETURN INFORMATION

C841M-A (7/02) 15 REVISION HISTORY Manual # Date Comments C841M 12/99 Original version. C841M-A 7/02 Updated manual to new format. Removed reference to alarm breakout panel. PRODUCT WARRANTY AND RETURN INFORMATION Pelco, the Pelco logo, Camclosure, Esprit, Genex, Legacy, and Spectra are registered t...