Pelco TXB-V - Manuals - manualsarea.com

Page 2 - Contents; List of Illustrations

2 C656M-E (04/07) Contents Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Important Notice. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

Page 3 - Important Safety Instructions; Important Notice; CAUTION

C656M-E (4/07) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Only use attachments/accessories specified by the manufacturer. 6. Installation should be done only by qualified personnel and conform to all lo...

Page 4 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

4 C656M-E (4/07) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired...

Page 5 - Description; Parts List

C656M-E (4/07) 5 Description The TXB-V translator board allows Vicon ® controllers to communicate with Pelco’s ExSite ™ , Esprit ® , and Spectra ® systems. After setup, the controller functions the same as a Vicon controller normally would, except as noted in the Operation section on page 21. The TX...

Page 6 - Esprit Installation

6 C656M-E (4/07) Esprit Installation To install the TXB-V translator board in an Esprit system (refer to Figure 1): 1. Turn off power to the Esprit system. 2. Remove the left cover from the pan and tilt. 3. Remove the shorting plug from the 16-pin connector on the Esprit system’s circuit board. 4. R...

Page 10 - Spectra III/Spectra IV Installation

10 C656M-E (4/07) Spectra III/Spectra IV Installation To install the TXB-V translator board in a Spectra III/Spectra IV Series: 1. Turn off power to the dome system. 2. Remove the lower dome. 3. Remove the dome drive by pressing in the blue and red tabs on the sides of the dome drive. Gently rock th...

Page 14 - Spectra Mini Dome Installation

14 C656M-E (4/07) Spectra Mini Dome Installation To install the TXB-V translator board in a Spectra Mini dome: NOTE: Installing a TXB-V into a mini dome increases unit height. In surface mount installations, you must cut a hole in the surface to accommodate the TXB-V cover. For an installation templ...

Page 18 - ExSite Installation

18 C656M-E (4/07) ExSite Installation To install the TXB-V translator board in an ExSite unit: 1. Turn off the power to the ExSite system. 2. Remove the pan and tilt unit from the power module (refer to Figure 16 and Figure 17): a. Loosen the setscrew in the locking ring with a 2 mm Allen wrench. b....

Page 21 - SPECIAL FUNCTIONS DEFINITIONS

C656M-E (4/07) 21 Operation Set preset 94 to access the camera menus. Press Iris Open to select menu items. The following table shows how the Vicon keyboard relates to the Pelco translator. Refer to your Vicon documentation for operating instructions. SPECIAL FUNCTIONS DEFINITIONS * Spectra SD53CBW ...

Page 22 - TXB-V ZONE PROGRAMMING PROCEDURE

22 C656M-E (4/07) TXB-V ZONE PROGRAMMING PROCEDURE A zone is a pan area, defined by a left and right limit, on the 360-degree pan plane. To program a zone using a Vicon controller (refer to the manual supplied with the controller): IMPORTANT: (Spectra III/Spectra IV and ExSite systems only): After p...

Page 23 - Troubleshooting

C656M-E (4/07) 23 Troubleshooting Symptom Possible Cause Suggested Remedy No video is displayed. Power is not connected to the Pelco unit. Check the power connector. Video cable is not connected to the Pelco unit. Check the video connector. Translator board is not inserted properly. Reinstall the tr...

Page 24 - Appendix

24 C656M-E (4/07) Appendix Table A. Receiver Address Settings Receiver Address Switch Setting 1 2 3 4 5 6 7 8 1 ON OFF OFF OFF OFF OFF OFF OFF 2 OFF ON OFF OFF OFF OFF OFF OFF 3 ON ON OFF OFF OFF OFF OFF OFF 4 OFF OFF ON OFF OFF OFF OFF OFF 5 ON OFF ON OFF OFF OFF OFF OFF 6 OFF ON ON OFF OFF OFF OFF...

Page 31 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on fiber optic products and TW3...