Pelco TW3004AR - Manuals - manualsarea.com

Page 3 - Important Safety Instructions

C1667M (6/06) 3 Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manu...

Page 4 - Regulatory Notices; RADIO AND TELEVISION INTERFERENCE

4 C1667M (6/06) Regulatory Notices This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired ...

Page 5 - Description

C1667M (6/06) 5 Description The TW3004AR is a four-channel active receiver that can receive live video over unshielded twisted pair (UTP) cable. The adaptive technology in the TW3004AR automatically adjusts the low , medium, and high frequency components of the video signal, allowing for the best po...

Page 6 - PARTS OF THE RECEIVER; Rack Power Connector:

6 C1667M (6/06) PARTS OF THE RECEIVER v Figure 1. TW3004AR Parts Rubber Feet (4): For placing unit on a flat surface, such as a desk or shelf. Status LEDs (4): Light red when there is no UTP video being received. Light green when there is UTP video being received. Flash amber when Coaxitron pan/tilt...

Page 7 - Installation; MOUNTING; USING A RACK

C1667M (6/06) 7 Installation The following parts are supplied: 1 Universal power supply (Part #PS04-1502-0512G) 1 Wall clip with screws and washers 1 Power connector 2-pin 1 UTP mating connector 1 Screwdriver MOUNTING The TW3004AR receiver is 3 rack units high and can be mounted into a fi ber rack, ...

Page 8 - USING A WALL CLIP

8 C1667M (6/06) USING A WALL CLIP To attach the TW3004AR receiver to a wall using the supplied wall clip, refer to Figure 2 and do the following: 1. Attach the wall clip to a wall using two screws (not supplied). 2. Slide the receiver into the clip until the two holes on the bottom of the receiver a...

Page 9 - SETTING THE DIP SWITCHES

C1667M (6/06) 9 SETTING THE DIP SWITCHES The factory default switch positions are shown in Figure 3. Switches 2-5 are set to auto and switch 1 is set to H mode. These settings ensure that the adaptive technology in the TW3004AR automatically adjusts the low, medium, and high frequency components of ...

Page 10 - APPLICATIONS; Cable Type

10 C1667M (6/06) APPLICATIONS You can connect the TW3004AR active receiver to transmitters, such as the TW3001P passive transceiver, and the TW3001AT active transmitter, and to Pelco UTP cameras, such as the CC3710/CC3610 series. Although you can connect these products using an unshielded twisted pa...

Page 17 - Specifications; ELECTRICAL

C1667M (6/06) 17 Specifications ELECTRICAL Input Voltage 12 VDC or 24 VAC, 50/60 Hz Power Consumption 10 watts Wire Type Unshielded twisted pair (24 AWG minimum) Wire Category Cat3 or better DC Loop Resistance 52 ohms per 1,000 ft (305 m) Differential Capacitance 19pF/ft max Transient Immunity 300 W...

Page 19 - PRODUCT WARRANTY AND RETURN INFORMATION

PRODUCT WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective in material or workmanship for a period of one year after the date of shipment. Exceptions to this warranty are as noted below: • Five years on FR/FT/FS Series fiber optic ...