Pelco SS3002 - Manuals - manualsarea.com

Page 2 - REVISION HISTORY; CONTENTS; LIST OF ILLUSTRATIONS

2 PELCO Manual C428M-B (2/98) REVISION HISTORY Manual # Date Comments C428M 3/87 Original version. C428M 5/90 Rev. A. Revised Section 4.3, Connector Assembly,procedures; Section 4.5, Adjustments, for addition offixed limit stop; and Section 6.0, Mechanical Part List.Figure 1 parts listed revised C42...

Page 3 - The product and/or manual may bear the following marks:

PELCO Manual C428M-B (2/98) 3 1.0 GENERAL Please thoroughly familiarize yourself with the information in this manual prior to installation and operation. 1.1 IMPORTANT SAFEGUARDS AND WARNINGS Prior to installation and use of this product, the following WARNINGS should beobserved. 1. Installation and...

Page 5 - CONDUCTOR AND CABLE REQUIREMENTS; WIRING INSTRUCTIONS; If you are not using the

PELCO Manual C428M-B (2/98) 5 3.0 INSTALLATION Save the shipping carton and plastic packing in case the unit has to be returned forcredit or repair. 3.1 CONDUCTOR AND CABLE REQUIREMENTS Before installing the pan and tilt, determine the conductor requirements and lengthof cable you will need to run b...

Page 7 - Figure 2. Connector Assembly; CONNECTOR ASSEMBLY; Contacts cannot be removed

PELCO Manual C428M-B (2/98) 7 Figure 2. Connector Assembly STEPS 3-7 1 5 10 16 23 29 34 9 15 22 28 33 37 4 FRONT VIEW 37-PIN CONNECTOR 1 FRONT VIEW 3 7 11 14 15 16 10 6 2 16-PIN CONNECTOR 1 4 FRONT VIEW 9-PIN CONNECTOR 3 6 7 9 1 4 FRONT VIEW 14-PIN CONNECTOR 3 7 8 11 12 14 1 9 15 4 FRONT VIEW 28-PIN...

Page 8 - Figure 3. Mounting Configurations

8 PELCO Manual C428M-B (2/98) Figure 3. Mounting Configurations 3.4 MOUNTING The SS3000 enclosure is designed to be suspended from a suitable length of 1-1/2"pipe threaded at both ends. This pipe can be interfaced to either a Pelco MRWAwall adapter, MRCA ceiling adapter, or coupled to a longer l...

Page 9 - Figure 4. Locking the Pipe Nut

PELCO Manual C428M-B (2/98) 9 3.4.1 Ceiling/Wall Mounting 1. Select an appropriate length of 1-1/2" NPT pipe for the mount you have se-lected. Once the mount is installed, insert and tighten the pipe to approxi-mately 30 ft lb, then tighten the 8-32 screw in the pipe nut to lock the pipethreads....

Page 10 - Figure 5. SS3000 Exploded Assembly Diagram; The “Schneider” ring is not

10 PELCO Manual C428M-B (2/98) Figure 5. SS3000 Exploded Assembly Diagram NOTE: The “Schneider” ring is not shown in this diagram. It is de-signed to fit over the square por-tion of the upper dome (item 1). 9. Turn the system on and rotate the pan/tilt. Check for cable interference. Tilt thecamera u...

Page 13 - MECHANICAL PARTS LIST; Table A. SS3000 Exploded Assembly Diagram (Corresponds to Figure 5)

PELCO Manual C428M-B (2/98) 13 5.0 MECHANICAL PARTS LIST Table A. SS3000 Exploded Assembly Diagram (Corresponds to Figure 5) Item No. Quantity Description Part Number 1 1 Dome, upper SS300010000 2 1 Dome, lower, smoked (SS30, SS3000) SS300010001* Dome, lower, chrome (SS3002) SS331100* 3 1 Bracket, u...

Page 15 - GENERAL

PELCO Manual C428M-B (2/98) 15 GENERAL Construction: Upper dome: Black, U.L. 94HB rated ABS plastic Lower dome: Acrylic hemisphere with distortion free viewing window withlight attenuation factor of 1 f-stop (SS30/SS3000) or mirroredlower dome with 2 f-stop (SS3002). Rotates with pan and tilt,camera...

Page 16 - WARRANTY AND RETURN INFORMATION; WARRANTY

16 PELCO Manual C428M-B (2/98) 7.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one year after the date of shipment. Excep-tions to this warranty are as noted below: • Two years on al...