Pelco SS22 - Manuals - manualsarea.com

Page 2 - REVISION HISTORY; LIST OF ILLUSTRATIONS; CONTENTS

2 Pelco Manual C429M-B (2/98) REVISION HISTORY Manual # Date Comments C429M-A 10/94 Wire colors revised on figures 2-4, 6 and 7. (Pin 8 -Figure 2; Pins 8 & 23 - Figures 3 and 4; Pins 8, 11, 12,13 - Figures 6 and 7.) C429M-B 7/96 Revised to include new models SS22 and SS2002-SL. 8/96 Revised Sect...

Page 3 - This device is; Please thoroughly familiarize yourself with the information; The product and/or manual may bear the following marks:

Pelco Manual C429M-B (2/98) 3 1.0 GENERAL CAUTION: This device is designed to operate at 24volts AC power. Input volt-ages must not exceed 28volts or drop below 22 volts,or else damage the themotors will occur. Shouldyou need technical assis-tance, please call (800) 289-9100. Please thoroughly famil...

Page 5 - CONDUCTOR AND CABLE REQUIREMENTS; PP Models; The following are cable re-

Pelco Manual C429M-B (2/98) 5 3.0 INSTALLATION Save the shipping carton and plastic packing in case the unit has to be returned forcredit or repair. 3.1 CONDUCTOR AND CABLE REQUIREMENTS A minimum of 11 conductors plus coax is required, which includes common re-quirements for motorized zoom lens and ...

Page 9 - Figure 5. Connector Assembly; CONNECTOR ASSEMBLY; Contacts cannot be removed

Pelco Manual C429M-B (2/98) 9 Figure 5. Connector Assembly 3.2 CONNECTOR ASSEMBLY To install and test the SS2000/SS2002 Series dome you will need to assemble theconnector parts provided. Fabricate the interconnecting cable as outlined below(see Figure 5): 1. Slide the cable clamp (part A , item 1) o...

Page 11 - Figure 8. Mounting Configurations; WALL MOUNTING

Pelco Manual C429M-B (2/98) 11 3.3 MOUNTING The SS2000/SS2002 enclosure is designed to be suspended from a suitable lengthof 1-1/2" pipe threaded at both ends. This pipe can be interfaced to either a PelcoMRWA wall adapter, MRCA ceiling adapter, or coupled to a longer length of pipe.Refer to Fig...

Page 12 - DOME INSTALLATION; The small hole in the upper

12 Pelco Manual C429M-B (2/98) 3.4 DOME INSTALLATION To install your dome system, perform the following steps (refer to Figure 9): 1. Select the appropriate pipe length and mounting method. If the MRCA or MRWAmount is used, tighten the pipe to approximately 30 ft lb, then tighten the 8-32screw in th...

Page 13 - EXPLODED ASSEMBLY DIAGRAM

Pelco Manual C429M-B (2/98) 13 4.0 EXPLODED ASSEMBLY DIAGRAM Table A. SS2000/SS2002 Exploded Assembly Diagram Item Qty Description Part Number 1 1 Dome, upper SS200010000 2 1 Dome, lower, Black (Opaque) SS200010001* Dome, lower, Chrome (Opaque) SS2012000* 3 1 Bracket, drive SS20004007COMP 4 1 Bracke...

Page 15 - Figure 10. Limit Stop Locations; Do not attempt

Pelco Manual C429M-B (2/98) 15 5.0 ADJUSTMENTS To adjust the pan/tilt limits, perform the following steps. Refer to Figure 10 for limitstop locations. Factory pan limits are set to 0-355 ° and tilt limits are set to 0-90 ° (horizontal to vertical). Under normal conditions, the tilt limits should not...

Page 18 - GENERAL

18 Pelco Manual C429M-B (2/98) GENERAL Maximum Camera/Lens Length: 12.5 inches (31.75 cm) AmbientTemperatureRange: 35 ° F to 120 ° F (1.6 ° C to 48.8 ° C) Construction Upper dome: Black, high-impact plastic, ABS Lower dome: Acrylic hemisphere with distortion-free viewing window withlight attenuation...

Page 19 - NOTES

Page 20 - WARRANTY AND RETURN INFORMATION; WARRANTY

20 Pelco Manual C429M-B (2/98) 8.0 WARRANTY AND RETURN INFORMATION WARRANTY Pelco will repair or replace, without charge, any merchandise proved defective inmaterial or workmanship for a period of one year after the date of shipment. Excep-tions to this warranty are as noted below: • Three years on ...